Yes, moving plumbing on a slab is possible but it is also quite challenging. Most plumbing is planned out prior to concrete being poured, so once it is set, it can be difficult to relocate. It will typically require digging a trench to access the pipes and then cutting and re-running the pipe.
This can be costly, invasive, and time-consuming. If it is possible to relocate the pipes, it will likely require professional plumbing expertise and a thorough review of the building and other factors that may be impacted.
Additionally, moving plumbing on a slab may also require acquiring the proper permit, additional materials or tools, and a clear plan to complete the process. For these reasons, it is essential to carefully consider if moving plumbing on a slab is worth it before taking any action.
How much does it cost to reroute plumbing in slab?
The cost of rerouting plumbing in a slab can vary greatly depending on a number of factors such as the complexity and length of the job, the accessibility of the area that needs to be rerouted, and the materials and labor involved.
Generally, however, the cost to reroute plumbing in a slab can range from about $2,400 to $8,000 for a medium-sized job. This cost might include replacing existing pipes and running new pipe inside the slab, as well as installing valves, cleaning the area in preparation for excavation, and doing any necessary patching or repair work afterwards.
Other factors that might increase the cost of the project include the cost of any ancillary work such as laying new cement around the area or grouting between newly installed pipes and the slab. Additionally, any difficulties encountered during the rerouting process can add to the cost of the job.
How hard is it to move a toilet in a slab foundation?
Moving a toilet in a slab foundation can be quite difficult, depending on the size and scope of the task. If the toilet is in a bathroom or on a concrete slab, then moving it will involve cutting through the concrete, which is not a simple or easy task.
Removing the old toilet will require some tools, such as a hammer, chisel and grinder. Depending on the plumbing setup, moving the toilet may also involve turning off the water and draining the existing water lines.
After the old toilet is removed and the new one is in place, the plumbing will have to be reconnected and the new toilet re-anchored to the floor. If the new toilet is in a different location than the original, a new water line will be added.
To ensure the best installation, it is often recommended to hire a professional plumber to complete the job.
How hard is it to relocate plumbing?
Relocating plumbing can be a challenging, time-consuming job that requires careful planning and specialized skills and experience. Depending on the complexity of the project, an experienced plumber may need to expand, shorten, or even completely re-route existing pipes and drainage systems to relocate plumbing fixtures like sinks, toilets, showers and bathtubs.
Any project of this nature needs to consider all factors, including local building codes and the layout of existing piping, to ensure that all repositioned plumbing is done properly and safely. Additionally, all new fixtures must also be installed per manufacturer instructions and also meet all applicable codes.
Depending on the particular project, relocating plumbing may require additional reinforcement and/or need to be retrofitted with new fixturing and pipes. All of this can create considerable additional costs and time commitments that must be factored into a project, making the relocation of plumbing an involved—and potentially costly—endeavor.
Is it expensive to move sink plumbing?
Moving sink plumbing can be expensive, depending on what you want done and the complexity of the job. The costs associated with the project can include the labor and materials necessary to move the sink and the associated plumbing, as well as the cost of any permits that may be required.
If invasive plumbing changes are needed, such as the need to move a gas line or water line, the costs can be higher. Additionally, if you do not already have the necessary plumbing supplies, pipes, and connectors on hand, they will need to be purchased, also adding to the overall cost.
How do I move plumbing from one wall to another?
Moving plumbing from one wall to another usually requires cutting into the wall and rerouting the pipes. You will need to turn off the water supply, identify the type of pipe that the plumbing is currently using, and decide how it needs to be rerouted.
Depending on the amount of piping that needs to be moved, you may have to cut into the walls to access the pipes. Once the new path for the plumbing has been identified, the old pipes will need to be cut out, new pipes cut to fit, and the new pipes inserted.
Finally, you’ll need to reconnect the pipes to the water supply, checking for any leaks before finishing the job. It’s recommended that you consult a professional plumber when moving plumbing from one wall to another, to make sure the job is done correctly and efficiently.
Can you move a floor drain?
Yes, it is possible to move a floor drain. It is not a difficult process, but it will require some precise work and some tools. Before beginning the project, you will need to know the location of both the existing and the proposed floor drain.
The first step is to remove the concrete around the existing drain to expose it. If there are any metal grates, those will need to be removed as well. Once the drain is exposed, you will need to remove the piping from beneath the drain.
After the piping is removed, you can begin to cut out the concrete from the new location. Once the new location is cut, the drain can be connected to the new piping and then the concrete can be poured in around the new drain.
Finally, any metal grates can be reinstalled. This project does require a certain level of skill, so working with an experienced professional is recommended.
How do you move a bathtub drain in concrete?
If you need to move a bathtub drain in concrete, there are a few steps you must take to ensure the project is successful. First, you will want to purchase a diamond-tipped circular saw blade that can cut through concrete.
Then, mark the spot where you want to cut with a marker or chalk line. To minimize dust accumulation, you should attach a vacuum hose to the saw and make sure to wear appropriate safety gear. With the saw turned off, make the first cut into the concrete floor.
Working carefully and slowly, use the saw to make a circular cut around the drain. Once you’ve created a sizeable hole, use a hammer and chisel to break apart the remaining concrete. Next, remove the drain and loosen the pipes connected to it with a wrench.
Finally, position the new drain in the hole and connect the plumbing pipes. To complete the project, use concrete patching material to fill in the hole around the drain. For the best results, wait for the cement to dry before use.
Slip a layer of caulk around the sides of the new drain to create a water-tight seal.
How do you replace plumbing under a slab?
Replacing plumbing under a slab involves a few important steps. First, the interior of the slab needs to be accessed, which typically entails busting out, drilling, or saw cutting a hole in the concrete.
Once the hole is made, an air hammer, core drill, or jack hammer can be used to remove the existing concrete and access the existing plumbing.
The existing plumbing needs to be disconnected and removed from the slab. This can be done with a pipe cutter, wrenches, and other necessary tools. Then the new plumbing lines need to be connected to the existing supply lines on the house’s exterior.
If the supply line is PVC, a coupling fitting will generally be used. It’s important to make sure the connections are threaded and glued securely.
Next, the plumbing should be tested to ensure there are no leaks. The new plumbing should then be buried in the cavity created when the original concrete was removed. A hydraulic bed should be used to hold the pipes and secure them in place.
Any fractures in the slab should be filled in with a concrete mixture before the slab is sealed back up. Finally, the area should be backfilled, tamped, and sealed with a concrete mix.
How do I find the drain pipe under my concrete floor?
Finding the drain pipe under your concrete floor can be a tricky process. It’s important to use caution and take safety precautions before beginning any project that involves digging or cutting concrete.
The best way to locate a drain pipe under a concrete floor is to use a specialized drain pipe locator tool. This tool emits high frequency sound pulses that travel through pipes and through the ground, allowing the user to pinpoint its location.
If you don’t have access to a locator tool, you can still locate your drain using the old “dig and find” approach, but this is much more difficult and potentially more dangerous.
Start by measuring the areas of the floor that need to be cut away, and mark off the areas with chalk or tape. Make sure to wear proper safety gear, such as goggles, dust masks, gloves, and earplugs.
Using a jackhammer or other demolition tool, start breaking away the concrete in the marked areas, taking care to avoid damaging the existing piping. Be sure to use gradual, even strokes. You may have to employ the help of a professional contractor or plumber to assist in the demolition process.
Once you have cleared away the concrete, you can use a flashlight to inspect the area and locate the drain pipe. With some luck, you should find it without too much trouble. If not, you can always use a plumbing snake to trace the pipe’s path.
As an alternative, you can also use a drain camera to get a clear picture of the pipes and determine exactly where it’s located.
Regardless of the method you choose, it’s important to keep safety in mind throughout the process. Make sure to take all necessary safety precautions, including wearing protective gear, and seek help from a professional if needed.
What is a plumbing reroute?
A plumbing reroute is the process of changing a plumbing system so that water or other liquids flow in a different direction or a different location. This can include anything from major reconfigurations, such as diverting sewer lines, to smaller modifications, such as rerouting pipes in a bathroom.
Commonly, plumbing reroute services are completed due to renovation, repairs, and remodeling. A plumbing reroute can also be necessary if a house or building is being shifted from one place to another.
Plumbers typically assess existing systems and provide evaluations on the best way to approach a reroute. This depends on the size of the project and existing systems in place. Certain reroutes will require cutting and disconnecting existing pipes, and then reconnecting them in the new location.
This process often includes the proper installation of new pipes, fittings, drainage systems, and other materials. Plumbers may also use trenchless technologies to quickly and efficiently reroute pipes.
Rerouting plumbing may take time and effort, so it is important to hire professional plumbing services to ensure the job is done correctly. A professional plumber can also ensure that the job is completed according to all relevant safety and building regulations in the area.
Can toilet plumbing be moved?
Yes, toilet plumbing can be moved. In general, the process would involve disconnecting the water supply, moving the toilet to the new location and then reconnecting the water supply. Depending on the age of the toilet and the complexity of the plumbing, additional components such as piping and fittings may need to be moved as well.
If the existing plumbing is difficult to work with or outdated, it may be beneficial to replace all fixtures with new ones. Otherwise, the plumbing should be inspected and tested to ensure that there are no leaks or other issues prior to installation.
In some cases, it may be necessary to call a professional plumber to complete the job.
Can you rotate a toilet 90 degrees?
Yes, you can rotate a toilet 90 degrees. Before rotating a toilet, it is important to consider whether it is appropriate to do so. The shape of the pipes and the layout of other plumbing fixtures in the room should be assessed carefully to determine whether it is feasible to rotate a toilet 90 degrees.
It is also important to ensure that the toilet is firmly secured to the floor and the toilet connections are accessible and properly positioned before it is rotated. Additionally, it is important to ensure that the wax ring between the toilet and the floor flange is sealed properly prior to rotating it.
If the toilet is located in a tight space, you may need to consult with a professional plumber to ensure that the toilet can be rotated safely. Additionally, it is important to note that a toilet may need to be re-leveled after it is rotated.
What is the labor cost to install a toilet?
The labor cost to install a toilet varies depending on the type of toilet you choose, the current plumbing layout of your bathroom, and the complexity of the installation. Generally, the labor cost to install a standard toilet runs between $125 – $225.
Some additional costs for labor may include disconnecting an old toilet, moving a new one into the location, resetting the flange, and installing a wax ring. If any plumbing alterations are needed, the cost of labor will be higher to accommodate for the additional labor involved.
Additionally, many installation companies may have additional charges for fuel and supplies, such as piping, fasteners, and other necessary elements.
Can you switch a toilet and shower?
Yes, you can switch a toilet and shower. Depending on the layout of your bathroom and available space, you may want to switch the toilet and shower to make better use of bathroom square footage. It’s generally easier to switch these two fixtures when you’re renovating the bathroom or during the initial building stage.
Generally, the best way to switch a toilet and shower is to get help from a professional. A professional plumber can explain the necessary steps needed to relocate the water supply pipes and drain lines to ensure everything is installed correctly, safely and according to municipal codes.
They can also recommend fixtures that meet your budget and needs while simultaneously considering the available space. For example, a corner shower provides much more space than traditional tub/shower combos.
If you’d like to switch the toilet and shower on your own, it’s important to review all of the local codes and guidelines first. Any excavation required most likely requires a permit, so be sure to research this aspect prior to starting any work.
Additionally, be sure to turn off the water to the bathroom while making the switch. Make sure to double check the installation and reconnect them to their lines before turning the water back on.
Can a toilet and shower share the same drain?
Yes, a toilet and shower can share the same drain. This is a common setup in many bathrooms. Generally, the waste from the shower passes through the shower drain, while the waste from the toilet passes through a separate pipe that is connected to the main sewer line.
When the bathroom is designed correctly, the shower water and toilet waste will not mix. The toilet waste is usually diverted away from the shower drain and the shower water is not able to enter the toilet drain.
For this setup to work, the drain pipes must be designed correctly and must be regularly maintained to ensure that nothing is blocking the pipes or mixing the waste water. If done correctly, having a shared drain for a toilet and shower can be a great way to save space in the bathroom and make for an efficient setup.
Are shower pipes connected to toilet pipes?
No, shower pipes and toilet pipes are not connected to one another. Shower pipes are typically connected to your home’s water supply whereas toilet pipes are connected to your home’s drain system and sewer.
Both of these pipes serve different purposes and therefore they must remain separate. Additionally, water from your shower will never end up inside of your toilet and waste water from the toilet will never end up inside of your shower.
Separating the two pipes ensures that there is no cross contamination or hazardous mixing of the two.