Yes, you can use other solutions in the Bissell CrossWave. Many of our customers have had success with all-natural, biodegradable, and non-toxic solutions in their CrossWave. This includes mixes of vinegar, dishwashing liquid, baking soda, and hydrogen peroxide.
However, it’s important to note that some substances may damage your CrossWave, so it is always important to test any non-Bissell solution on a small hidden area of the floor before using it on the entire surface.
Additionally, the concentrations for the solutions should never exceed what the manufacturer recommends for use in the CrossWave. When using non-Bissell solutions, it’s also important to ensure that you completely rinse any residue from the cleaning pads and the surface before changing between wet and dry vacuuming modes.
Finally, you should never mix different solutions as this could cause chemical reactions and damage the surface of your floors.
What chemicals can you use in the Bissell CrossWave?
The Bissell CrossWave can be used with an array of cleaning chemicals for all kinds of surfaces. For wood floors, you can use any kind of cleaners designed for hard floors such as vinegar or ammonia solutions.
For carpets and rugs, you can use upholstery shampoo from any store, but it is best to use Bissell’s Multi-Surface pet formula. For tiled surfaces, you can use any kind of tile cleaner like a concentrated solutions of hydrogen peroxide, but be careful to not use cleaning chemicals that contain bleach, as this can damage the surface.
For upholstery and fabric, use Bissell’s Upholstery cleaning formula and avoid using any other kind of fabric cleaner, as any other kind of cleaner could damage the fabric. For pet messes, it is best to use Bissell’s Pet Stain and Odor formula to remove any type of pet waste or mess.
Lastly, it is important to check the instructions on the cleaner to ensure it is suitable for the surface you are cleaning and in the correct quantity.
What formula does Bissell use?
Bissell uses a “dual dirt lifter power brushes” formula which effectively cleans carpets and upholstery, also commonly referred to as the “Dual Rotating Cleaner”. This formula utilizes rotating dual brush rolls that simultaneously remove deep-down dirt and grime, while also providing additional suction to capture more dirt and debris.
This formula is designed to provide deep-cleaning results that are superior to other carpet cleaners in terms of time and effectiveness. The rotating action of the dual-brush rolls also helps lift and loosen stubborn dirt, stains, and messes for effortless and out of sight cleaning.
Additionally, thanks to the included suctioning power, these messes are whisked away and captured in a large-capacity tank. This ensures that messes are removed quickly, easily, and mess-free. Bissell also offers supplemental floor cleaning formulas, such as the “PowerSteamer” that cleans hard floors without the need for harsh or annoying chemicals.
Combined with the patented dual-brush cleaning formula, Bissell offers a powerful, efficient, and effective solution for any type of cleaning job.
Can I use Pine Sol in my CrossWave?
Yes, you can use Pine Sol in your CrossWave. However, it is important to remember to dilute the Pine Sol before use. To do this, mix 1/4 cup of Pine Sol per 1 gallon of water. Once diluted, put it in the cleaning solution tank of your CrossWave, then run it through a cleaning cycle as you would with any other cleaning solution.
It is also important to remember that Pine Sol should never be used on unsealed wood surfaces or any other solid wood surfaces that may be damaged by the ingredients in the cleaner. Additionally, it is best to avoid using Pine Sol in areas with unfinished floors or grout lines.
How do you make a Bissell cleaning solution?
Making a Bissell cleaning solution is easy and only requires a few ingredients.
First, mix together 1/4 cup of white vinegar, 1/4 cup of baking soda, and 1/4 teaspoon of liquid dish soap in a bowl. Once the ingredients are combined, pour the mixture into a 32-ounce spray bottle and fill the rest of the bottle with warm water.
Replace the spray nozzle and shake the bottle to combine the ingredients.
To use the solution, spray it directly on the affected area and use a clean cloth, brush, or sponge to scrub the area. Then rinse the area with warm water and let it air dry.
If the solution is too harsh or not effective enough, you can try adjusting the ratio of ingredients. For example, use more vinegar or baking soda to make it more effective or use less of either ingredient to make it milder.
Bissell cleaning solutions are a great way to make your home sparkle and keep it clean and odor-free. With a few simple ingredients and a few minutes of effort, you can make your own cleaning solution and save yourself time and money.
Can I put Pine Sol in my Bissell steam mop?
No, you should not put Pine Sol in your Bissell steam mop. The Pine Sol formula includes a special cleaning agent that could corrode the internal parts of the steam mop and possibly damage it. Additionally, using Pine Sol in the steam mop could cause a dangerous build-up of fumes and any residue of the Pine Sol left on the floors could be potentially hazardous to your health.
It is best to only use products that are designed specifically for steam mops so you can be sure they are safe to use and will not damage the machine. We recommend using the Bissell Hard Floor Cleaner or the PowerFresh Active Mop Pad Kit with the Bissell steam mop.
Which floor cleaners are pH neutral?
PH Neutral floor cleaners are ideal for neutralizing or balancing the alkaline or acidic pH levels found in certain flooring types, such as marble, granite, stone, or tile. Many commercially-available pH neutral floor cleaners are formulated using acidic solutions, though there are also many DIY solutions available for those looking for eco-friendly options.
Common ingredients found in pH neutral cleaners include vinegar (acetic acid), lemon juice (citric acid), baking soda, and borax. Unlike harsher commercial cleaners, these DIY solutions are less likely to damage or affect the look of your flooring.
To ensure you do not damage the floor with your cleaner, it’s important to check the pH level of your cleaning solution to make sure it is neutral.
Ground-in dirt, grime, and messes can often be hard to remove so it’s important to select a pH neutral cleaner that is designed to handle heavy, tough cleaning jobs as well. Examples of pH neutral, heavy duty floor cleaners include hydrogen peroxide, citrus oil and ammonia.
Be sure to keep your cleaner to a diluted solution when using chemical cleaners, and avoid using products with additives such as ammonia.
Ultimately, pH neutral floor cleaners are not only safer on your flooring but they are also often safer for the environment. When selecting a cleaner, be sure to select one that is designed to safely remove dirt, grime, and messes while also being pH neutral.
Is Bissell Multi Surface cleaner pH neutral?
Bissell Multi Surface cleaner is designed as a neutral formula that does not contain harsh chemicals, so it is considered to be pH neutral. It is not acidic or basic in its cleaning capabilities and won’t cause damage to surfaces that are sensitive to pH imbalances.
The unique Bissell formulation has been tested and proven to be non-corrosive, safe and effective at cleaning multiple hard surfaces without streaks or residue. It contains no phosphates or chlorine and is safe to use on sealed hardwood, linoleum, tile, vinyl, granite, and marble flooring.
Additionally, Bissell Multi Surface cleaner is safe to use on counters and other household surfaces, including electronic devices and kitchen appliances, without damaging the finish or leaving any hazardous residue.
With Bissell Multi Surface cleaner, you can enjoy an effective clean without worries or concerns of staining, damaging, or degrading surfaces.
Do you have to use Bissell CrossWave solution?
No, you do not have to use Bissell CrossWave solution with the Bissell CrossWave. Although the CrossWave solution is designed to perfectly clean and protect your floors, you can use any other multi surface cleaning solution that is suitable for sealed hard floors.
However, it is important to not use soap that is designed for manual cleaning as it can affect the performance of the machine, leave a residue and cause damage to your floors. Furthermore, it is important to use a solution that is specific to the type of floors that you have, such as wood or tile.
Additionally, keep in mind that you need to use solution with the CrossWave in order to activate and maintain the brush system, or else you may run into problems.
Why is my Bissell CrossWave leaving dirty water?
It is possible that there are a few different reasons why your Bissell CrossWave is leaving dirty water on your floors. It could be caused by a clogged filter, dirty water tank, or a broken pump. It is important to regularly check the tank, filter, and other components of your machine to make sure they are working properly.
If your filter is clogged, it can result in the machine not sucking up the dirty water properly. To prevent this, check the filter regularly and clean off any debris.
If the pump is broken, or not functioning correctly, it will result in dirty water being left behind. You may need to inspect the pump and clean or replace it if necessary.
If the tank is dirty, this can also cause the water to be dirty when released from the machine. To prevent this, make sure to regularly clean the tank and get rid of any buildup in the tank.
By regularly maintaining your Bissell CrossWave and checking filters and components, you can help avoid an issue with dirty water.
How much solution does a Bissell CrossWave need?
The amount of solution needed for your Bissell CrossWave depends on what type of solution you are using. If you are using the Multi-Surface Formula, you will need approximately one tablespoon for each 32 ounces of water.
For the Wood Floor Formula, you will need approximately one teaspoon for each 32 ounces of water. You do not need to use the entire amount with each filling of the tank. As long as the solution is properly mixed with your water, you can use less than the recommended amounts without a decrease in overall performance.
Additionally, be sure to only use solution specifically designed for the CrossWave and not a general all-purpose cleaner, as it could interfere with the machine’s performance.
Does the Bissell CrossWave vacuum and mop at the same time?
Yes, the Bissell CrossWave vacuum and mop at the same time. The Bissell CrossWave is a revolutionary product that cleans both hard surface floors and area rugs. It vacuums and washes them simultaneously, so you can efficiently clean all your floors with one machine.
The CrossWave cleans with a dual-action brush roll that is designed to lift and remove embedded dirt, debris and pet hair while the Multi-Surface formula gently washes your sealed hardwood, tile and laminate floors.
Plus, it has a separate setting for area rugs, so you can vacuum and wash rugs, simultaneously. The CrossWave also has an easy-fill tank, which holds the solution and water, and a special cleaning lever that allows you to switch from using the cleaner to using just water, so you can easily customize the amount of cleaner you want for every job.
So yes, the Bissell CrossWave does vacuum and mop at the same time.
Can the Bissell carpet cleaner be used as a vacuum?
Yes, the Bissell carpet cleaner can be used as a vacuum. The Bissell PowerForce Turbo Bagless Vacuum is a powerful carpet cleaner with a handheld vacuum that reaches places a standard vacuum cannot. It also comes with a detachable hose and tools, which can be used as a vacuum for cleaning as well as for deep cleaning carpets and upholstery.
The powerful suction from the TurboBrush can pick up dirt, dust and debris with ease, while the EdgeSweep feature ensures that dirt and debris is collected on the edges and corners for a thorough clean.
This vacuum also has a dirt cup for easy disposal, so the process of emptying it is made simple.
How much Bissell formula do I use?
The amount of Bissell formula you use depends on the type of cleaning job you are doing. For general cleaning and light stain removal, fill the tank to the 1-L line (1 liter) with hot tap water, then add 2 ounces (59 mL) of Bissell formula.
For heavy stain removal and especially for pet messes, fill the tank to the 1-L line with hot tap water and then add 4 ounces (118 mL) of Bissell formula. Always shake the formula bottle before measuring and dispensing to ensure an even mixture of concentrates and water.
Can you use the Bissell CrossWave with just water?
Yes, you can use the Bissell CrossWave with just water. This multi-surface cleaner is designed to deep clean both hard flooring and area rugs using a combination of an innovative suction system and brush roll to loosen, lift and remove dirt.
The CrossWave includes two tanks and a special solution that allows you to clean surfaces with both water and a cleaning solution. However, if you don’t want to use the supplied cleaning solution, you can simply fill the clean water tank with plain water and control the amount of water dispensed by adjusting the water dial.
This way, you can create your own mixture of water and cleaning solution or just use water if preferred.
How do you add a solution to a Bissell?
To add a solution to a Bissell vacuum, you’ll first need to locate the solution tank. For most models, it’s located near the top of your machine, and contains a measuring cup/spout and lid. Dispose of any old cleaning solution, then fill the tank with warm water up to the line indicated.
Depending on the type of solution you’re using, you’ll then add an appropriate amount of the product. For example, if the product recommends 1 capful per gallon of water, then add a measuring cupful of solution.
To ensure your machine is thoroughly cleaned, use a damp cloth to wipe out the inside and outside of the tank, paying particular attention to the spout. Fasten the lid securely, then return the tank to its normal position.
Finally, follow the manufacturer’s instructions for loading the solution into your machine and you’ll be ready to start cleaning.
How much carpet cleaning solution do I need?
The amount of carpet cleaning solution you need will depend on the size of the area you’re cleaning as well as the type of cleaner you’re using. Generally, you’ll need about 1.5-2 ounces of cleaner for every square foot of carpet you’re cleaning.
Most carpet cleaning solutions come with instructions on the label that will help you determine the exact amounts you need. You should always read the instructions carefully before you begin and follow them closely to ensure your carpet is properly cleaned.
Additionally, you should use the proper amount of solution for the type of machine you’re using — for instance, the amounts you use for a wet extraction machine will be different than what you use for a dry cleaner.
