Operating a Drill Doctor is fairly simple. Before you begin, make sure that you have all of the necessary components – like a power source, adapter and shank – ready and available.
1. Begin by inserting the bit you want to sharpen into the Drill Doctor chuck and tighten the chuck around the shank of the bit.
2. Securely position the bit against the chuck’s setting line. This will be the position of your sharpening point.
3. Plug the Drill Doctor into a power source and then turn on the power switch.
4. Before you actually sharpen the bit, let the Drill Doctor “prime” for 30 seconds.
5. After 30 seconds have elapsed, turn on the speed control knob which will cause the bit to start rotating at the recommended rate of 4000 – 6000 RPM.
6. To sharpen the bit, lightly push the bit against the sharpening stone.
7. Once the bit is sufficiently sharp (usually takes around 10-20 seconds), turn off the power switch and remove the bit from the Drill Doctor.
8. To complete the sharpening process, you may need to repeat step 6 and 7. This will help ensure that the bit has been sharpened as evenly as possible.
9. After you’re done sharpening the bit, turn off the power switch and unplug the Drill Doctor.
While operating a Drill Doctor may seem like a complicated process at first, it is actually quite simple once you get the hang of it. Following the above steps will ensure that you get the best end result possible.
How do you use a drill doctor 500x?
Using the Drill Doctor 500x is a straight-forward process. Start by clamping the bit in the chuck of the Drill Doctor and tightening the jaws firmly. Then adjust the depth stop collar to the desired depth.
Set the Sharpening Tables so that the bit is between the diamond wheel and the alignment bar. Set the Sharpening Angle selector to the desired angle and then turn on the Drill Doctor and give it a few seconds to reach full speed.
Once it reaches speed, start to feed the bit slowly into the diamond wheel. Keep a steady pressure and don’t push too fast. Let the machine do the work. After a few seconds, the bit should come out of the diamond wheel at the desired sharpening angle.
If you happen to get a little bit of burr on the bit, you can remove it with a cotton wheel and some compound supplied in the kit. Finally, lubricate the bit with Drill Doctor’s Bit Lube to prevent rusting and enhance drilling performance.
Is the Drill Doctor worth it?
Whether or not the Drill Doctor is worth it depends on your needs and budget. The Drill Doctor is a tool that works to restore and sharpen drill bits. It can sharpen both high-speed steel and black oxide drill bits, as well as split-point bits.
It also offers a range of grinding angles, which allows for custom angles.
The main appeal of the Drill Doctor is the convenience it offers. It eliminates the need to buy replacement bits and makes sharpening easier and faster than traditional methods. It also features a built-in alignment system, which makes it much easier to sharpen drill bits accurately and quickly.
On the other hand, the Drill Doctor is an expensive tool that is only suitable for sharpening drill bits. If you only use drill bits occasionally, the cost of the Drill Doctor is likely not worth it.
There are also other methods of sharpening drill bits such as using a file or bench grinder.
In conclusion, whether or not the Drill Doctor is worth it depends on your needs and budget. If you use drill bits regularly it could be a worthwhile investment, however if you use them only occasionally it might be better to look for cheaper alternatives.
Will Drill Doctor sharpen masonry bit?
No, the Drill Doctor will not sharpen masonry bits. This is because masonry bits are made of much harder materials than other drill bits and are designed to cut through harder materials like concrete and stone.
The Drill Doctor is designed to sharpen standard drill bits made of softer materials, such as steel and titanium. Masonry bits are usually made of high-speed steel (HSS) and will require more specialized sharpening techniques and tools to sharpen properly.
Therefore, it is recommended to have masonry bits professionally sharpened or replaced if they become dull.
How do you sharpen masonry bits with a Drill Doctor?
Sharpening masonry bits with a Drill Doctor is quite simple. First, mount the bit into the positioner at the top of the power sharpener. Secure the bit in the positioner and adjust the bit for the desired angle of sharpening.
Depending on the model, rotate the bit to the left or choose the stone size from the menu. Turn on the machine and set the stop collar so that the bit is sharpened to a consistent length. Feed the power sharpener slowly over the surface of the stone until a sharp edge is achieved.
Once the desired sharpening level is achieved, turn off the machine and unplug it. Carefully remove the bit from the positioner and clean any debris from the masonry bit with a damp cloth. Finally, inspect the bit to ensure that it is now sharpened and ready to use.
What angle should a drill be sharpened to?
The angle at which a drill bit should be sharpened depends on the type and size of the bit. Typically, a standard drill bit should be sharpened to a 118-degree angle. Bits such as brad point bits and wood auger bits should typically be sharpened to a 90-degree angle, and masonry bits should typically be sharpened to a 135-degree angle.
Countersink bits should usually be sharpened to an 82-degree angle. When sharpening a bit, be sure to be very precise in order to get the sharpest and most effective cutting edge. In most cases, it is best to use a specialized sharpening jig to ensure that the angles are exact.
Additionally, it is important to ensure that the cutting edges are kept in balance while sharpening.
Can coated drill bits be sharpened?
Yes, coated drill bits can be sharpened. However it is not recommended to do so, as the coating can be damaged in the process. It is much more efficient to simply replace the old bit when it has become worn out or dull.
Sharpening drill bits will require special tools as well as knowledge and experience to do it properly. By attempting to sharpen coated drill bits, the coating could be removed, leading to reduced performance.
If the coating has already been removed due to use, it is possible to sharpen the bit. If the drill bit is made from cobalt or high-speed steel, the edges should be reshaped with a specialty grinding wheel.
For those made from carbide, files should be used to sharpen the edges. However, in either case, it is recommended to seek the advice of an experienced professional.
Are drill sharpeners any good?
Yes, drill sharpeners can be helpful if your drill bits become dull or damaged. They come in a variety of types and are designed to quickly sharpen and extend the life of your drill bits. The most common type of drill sharpener is called a bench grinder.
This type of sharpener is designed to hold the drill bit in place and will run the drill bit against a rotating grinding wheel to sharpen the bit. They usually feature interchangeable grinding wheels and speeds to accommodate different types of drill bits.
Another popular type of drill sharpener is an electric drill sharpener. This type of sharpener is designed to plug into an electric outlet and features a rotating grinding wheel that is placed inside a chuck.
It is often easier to use than the bench grinder and may offer variable speeds for different types of drill bits. An abrasive sharpening stone is another popular, easy-to-use option for sharpening your drill bits, but it is more time consuming and requires some skill.
Whichever type of drill sharpener you choose, you can be sure that it will help to extend the life of your drill bits and help you get the job done faster.
What is a split point drill bit?
A split point drill bit is a type of drill bit designed to begin drilling quickly with minimal effort on the part of the user. It is so named because the tip of the bit is split into multiple parts. This split helps the bit get a grip on the material, and allows the bit to drill at lower speeds and torque, as well as reduce walking on surfaces when the drill is started.
The split technique also helps to reduce heat and vibrations from drilling, and makes the bit much less prone to getting stuck when drilling. Split point drill bits are available in many sizes and shapes, from small to large, and can be used on metal, wood, plastic, and other materials.
Is Titanium stronger than black oxide?
Titanium is often perceived as being one of the strongest and most durable metals available, withstanding wear and tear from all types of environments. However, when compared to black oxide, Titanium may not necessarily be the stronger choice.
Black oxide is a specialized form of corrosion-resistant coating that is commonly used on steel and iron parts. It is not a metal itself, but rather a strong chemical conversion coating that sacrifice itself to corrosion, leaving the underlying metal more protected than if the surface had not been treated.
Black oxide has excellent wear, chemical and electrical resistance, as well as a beautiful finish, making it ideal for items that not only need to look good, but also withstand damage from occasional exposure to moisture and chemicals.
However, while it might not be as strong as Titanium, black oxide is just as hard and resistant to wear, making it an excellent choice for components that need to last in harsher environments with less maintenance.
What are Pilot Point drill bits used for?
Pilot Point drill bits are a specialized type of drill bit used for making cleaner, more precise holes in a variety of materials. They have a unique point design that helps reduce the amount of time and effort needed to drill a hole compared to standard twist drills.
Pilot Point drill bits provide a more stable cutting point which helps reduce bit skipping or chattering, a common problem when using standard twist drills. Pilot Point drill bits can be used on a wide range of applications, from softwood to hardwood, plastic, composites, aluminum, stainless steel, and cast iron.
They are commonly used for making screw holes, joinery, manufacturing, repair, and remodeling projects.
