Skip to Content

How do you get a broken pipe out of a fitting?

Getting a broken pipe out of a fitting can be a difficult and time-consuming task. It is important to take the necessary safety precautions when attempting to remove a broken pipe from a fitting, as there are many dangers associated with the task.

The first step is to turn off the water source to the broken pipe. Once the water supply has been shut off, the broken pipe must be cut out of the fitting. It is recommended to use a hacksaw to cut out the broken pipe, as it is the safest way to remove it.

Once the broken pipe has been cut out, the next step is to remove the remaining pieces of the broken pipe. If possible, it is best to remove the pieces with a pair of pliers. However, if the remaining pieces of the broken pipe are too deeply embedded, you may need to use a chisel and hammer to carefully remove them.

Once all of the pieces of the broken pipe have been removed, the fitting must be inspected for any damage. It is important to repair or replace any damaged parts as soon as possible. Once the fitting is securely in place again, it can be reattached to the water supply.

Getting a broken pipe out of a fitting is a difficult task, but it is important to take the necessary safety precautions and use the necessary tools in order to avoid any potential damage or injury. Doing so will ensure that the task can be successfully completed.

How do you get PVC pipe apart after glued?

When it comes to separating PVC pipe after it has been glued, there is no easy solution. It will likely require a bit of effort and elbow grease on your part. The key to getting the pipes apart is patience and caution.

First, start by using a sharp chisel and hammer to gently tap and score a groove in the glue line between the two pipes. You should be patient and take your time while doing this, as you don’t want to damage the pipe.

After you have made a groove in the glue line, use a strong solvent or adhesive remover to break down the adhesive bond and soften it. Once softened, you can then use a flat-edged tool (like a putty knife) to gently pry the pipes apart.

If the adhesive remover doesn’t seem to be working, you may have to resort to other tactics like using an electric saw, and cutting the pipe apart. Be sure to wear protective gear, such as gloves and eye protection, whenever using any kind of power saw.

Can you Unglue a PVC fitting?

Yes, it is possible to unglue PVC fittings, but it requires particular tools and specific expertise. The most common method is to use a heat gun or flame torch to loosen the adhesive bond. This heat needs to be specifically localized and directed onto the glued surfaces and for a brief amount of time in order to prevent any damage to the PVC.

You may also need to use a lubricant or primer-type chemical to help loosen and dissolve the adhesive bond from the pipe and fitting. In some cases, it may be necessary to use a sharpened chisel or flat head screwdriver to break the fitting free.

Be sure to wear gloves and safety glasses when attempting to unglue PVC fittings.

Will a heat gun loosen PVC glue?

Yes, a heat gun can be used to successfully loosen PVC glue. Heat guns are ideal for this task because PVC glue softens when exposed to heat. Applying heat will loosen the adhesive, allowing the two pieces of PVC that were stuck together to be separated.

It is important to exercise caution when using a heat gun as they can become very hot. Applying a lower heat setting and moving the gun around in a circular motion will reduce the risk of scorching the PVC.

The amount of time it takes for the PVC glue to soften will depend on the heat setting and type of adhesive used. Additionally, for best results, a putty knife or similar tool can be used to help pry the two pieces of PVC apart.

How do you reuse old PVC fittings?

Reusing old PVC fittings is a great way to save money and conserve resources. Before attempting to reuse an old fitting, make sure there are no signs of deterioration or damage. If the fitting is in good condition and has not been used for a plumbing project, it can be reused in various ways.

One way to reuse old PVC fittings is by crafting them into something new, such as art pieces or garden decorations. Cutting the fittings into various shapes and sizes opens up a world of creative possibilities.

Another way to reuse old PVC fittings is to use them for everyday tasks. For example, you can use old PVC fittings as the foundation for a shoe organizer or as the center of a coat rack. These fittings can also make great holders for hanging towels, gloves, and scarves.

Finally, you can use old PVC fittings as part of a repurposing project. For instance, they can make great planters or trellises for plants and flowers. Additionally, old fittings can make excellent holders for simple everyday objects around the house, such as condiment bottles, small tools, or utensils.

Using old PVC fittings requires a bit of creativity and some handy know-how, but it can be a great way to extend the lifetime of the fittings and reduce your ecological footprint.

How do you bore out a plastic pipe?

Boring out a plastic pipe can require a specific set of tools depending on the size and type of pipe material you are using. Generally, the process entails cutting the pipe with a circular saw and adjusting a drill bit size to fit the diameter of the pipe.

Once you have the correct drill bit, insert the bit into the drill and drill the pipe until it is bored out. Additionally, it is important to ensure that the drill bit is dull in order to avoid any cracking or splitting of the pipe.

If the pipe is too thick for the drill to bore by itself, you can use a sharp metal reamer to widen the hole as you drill. Finally, use sandpaper to smooth out any remaining burrs or other imperfections left in the hole.

How do you loosen PVC pipe under sink?

To loosen PVC pipe under a sink, you will need to start by shutting off the water supply to the sink. Once the water is off, you can use adjustable pliers to loosen the PVC fittings. Take a pair of adjustable pliers and grip the PVC fitting firmly, then turn it counter-clockwise to loosen.

Depending on how tight the fitting is, you may need to tilt the pliers at an angle to get enough leverage to loosen the fitting. Additionally, you may want to use a lubricant, such as WD-40, to help loosen the fitting.

Simply spray it on the fitting and let it sit for a few minutes before attempting to loosen the fitting. Once the fitting is loose, you can then disconnect it accordingly.

How do you dissolve cement in PVC pipe?

Dissolving cement in PVC (Polyvinyl Chloride) pipe can be a difficult and tricky process. The cement needs to be completely dissolved before it will be able to be removed, but the process can be simplified.

The most important thing to do is to make sure that all the fits in the pipe have been loosened, and that the pipe can be easily worked. You will also need to make sure that the ball valve or other connection has been removed to clear the pipe.

Once the pipe has been adequately prepared, it is time to begin dissolving the cement. Mix together one and a half parts of white vinegar, one part baking soda and one part liquid detergent. This mixture is enough to cover around half of the pipe’s surface.

Using a paintbrush, apply the solution to the cement area and let sit for two to three minutes. Repeat this process a few times until the cement has begun to dissolve. After the cement has loosened, use a putty knife to scrape away the remnants.

To finish the job, rinse off the pipe and scrub the areas where cement was present with a soft brush and soap. This should remove any residual cement and ensure that the pipe is clean and ready for use.

Does vinegar dissolve concrete?

No, vinegar will not dissolve concrete. While vinegar is acidic and can dissolve some materials, it does not have the same chemical makeup as a concrete dissolver. Concrete is composed of cement and other materials like sand, gravel and water, so it is much more resilient than other materials.

If you were to put vinegar on concrete, it would sit on top and could in rare cases possibly etch or corrode the concrete, but it would not dissolve it. If you are trying to remove concrete, other options would be more effective like a chemical concrete dissolver.

However it is important to protect the surrounding environment and surfaces as most chemical concrete removers are caustic and toxic.

What will dissolve cement?

Cement, a type of bonding material, is composed of limestone and clay that is heated until it reaches a powdered consistency and is then combined with water to form a paste. In order to dissolve cement, the paste must be exposed to extreme temperatures.

Extreme heat will cause the particles of cement to melt, separating them from their bonding components and losing the adhesive properties that hold them together. In extreme cold, the paste becomes brittle and shatters into small particles.

Chemical agents, such as sulfuric, hydrochloric, and nitric acids, can be used to break down the bond of cement, although it can be dangerous as acids can corrode metals and cause burns on skin. To reduce the risk of corrosion or injury, these acids should only be used in well-ventilated areas.

Additionally, there are several chemicals available in the form of specialized solutions, such as muriatic acid, that are designed to safely and effectively dissolve cement.

How do you remove a broken threaded metal pipe?

Removing a broken threaded metal pipe can be difficult, depending on the size and materials of the pipe. Generally, the best approach is to use a specialized tool called a pipe wrench. A pipe wrench is a large adjustable wrench designed for gripping around the circumference of a pipe for tightening or loosening threaded metal pipe connectors.

Place the pipe wrench around the broken pipe and rotate in the direction of the loosening threads. Once the broken pipe has been loosened and the damaged area has been exposed, you can carefully remove the broken pipe and replace it with a new one.

If the broken pipe is difficult to reach or access, you may also be able to use a pipe extractor or specialized cutting tool to assist in the removal.

How do you use an internal pipe extractor?

An internal pipe extractor is a tool used to remove damaged or corroded pipes or fittings. The tool uses a long, flexible metal shaft with a winding mechanism that allows it to be threaded through existing pipes.

At the end of the shaft is a gripping mechanism that can grasp the damaged/corroded pipe, allowing it to be pulled through the pipe. To use an internal pipe extractor, first measure the inner diameter of the existing pipe and then select a pipe extractor with a gripping mechanism that matches it.

Next, feed the extractor shaft through the existing pipe. Once the extractor is entirely through you can start the winding mechanism to make the shaft grip the damaged/corroded pipe and then turn it counter-clockwise to begin to unwind the shaft.

This motion will cause the damaged / corroded pipe to be pulled through the existing pipe. Continue to use counter-clockwise motions to pull out the damage piece entirely. Finally, once the damaged/corroded pipe is extracted you can use the pipe extractor again to replace it with new pipe.

Can PVC pipe be taken apart?

Yes, PVC pipe can be taken apart. If your PVC pipe is cemented together with waterproof glue, you will need to use a pipe cutter to score the PVC pipe and cut off the lengths you need. To separate multi-piece fittings, you’ll need to use a PVC pipe saw and cut the fittings apart.

You can also use a hacksaw or miter saw with a reinforced steel cutting blade to cut through thicker fittings. It is important to be very careful when separating PVC pipe or fittings as they are very brittle and can easily crack if handled improperly.

Can PVC be unglued?

Yes, PVC can be unglued. It typically requires using a solvent to break down the adhesive and allow for separation. Common solvents used to unglue PVC include paint thinner, acetone, mineral spirits, or methyl ethyl ketone (MEK).

These can be applied to a cloth or rag and wiped onto the surface of the PVC to dissolve the glue. Heating the glue can also help, though it is important to be careful and avoid excessive heat, as this can cause warping and damage to the PVC.

It can also be helpful to use a putty knife or other thin tool to help scrape away at the glue to separate the pieces.

How do you break down plumbers glue?

Plumbers glue is a type of solvent cement used to connect piping materials together. It is designed to be strong and sturdy, and thus can often be difficult to break down effectively. However, there are several methods that you can use to break down plumber’s glue:

1. Hot Water/Steam – One of the quickest and most effective ways to break down plumbers glue is to use hot water or steam. Heat up a pot of hot water (or steam) and apply it directly to the glue. The goal is to heat the glue until it loses its adhesiveness, which may take some time depending on the glue’s composition.

With careful observation, you should be able to see the glue losing its strength and becoming easier to break down.

2. Dissolving Solvent or Chemical – If hot water/steam isn’t an option, then look for a solvent or chemical that is specifically designed to dissolve plumber’s glue. These can be found at most hardware stores, and should be applied directly to the glue according to the manufacturer’s instructions.

Then, allow the solvent or chemical to do its job and dissolve the glue, which should take less time than hot water/steam.

3. Cutting – If all else fails, the last option is to use cutting tools such as a saw, grinder, etc. to manually cut away the glue. Obviously, this is the most time consuming and labor intensive option, but it should still be able to do the job.

Just be sure to wear proper safety equipment when using cutting tools, as they can be dangerous if used improperly.

These are the three primary methods for breaking down plumbers glue. Depending on the situation, you may need to experiment with different approaches and combinations to get the best results. In any case, be sure to take the necessary safety precautions before attempting to break down the glue.

How do you fix a leaking PVC joint without cutting it?

In order to fix a leaking PVC joint without cutting it, the first step is to make sure that the joint is threaded correctly and the glue applied properly. If the leak is only a small drip, then it can sometimes be repaired by tightening the joint with a pipe wrench.

If tightening the joint does not work, you should apply a liquid sealer to the threads and then wait for it to dry. You should then add some plumber’s tape or a thin layer of putty to the joint, with the putty applied around the outside of the joint.

Using a pipe wrench, carefully secure the joint and then leave it to dry. This should result in a tight seal that will stop the leak. If the leak persists, you may need to replace the joint with a new one.

How do you Unglue Super glue?

The best way to unglue super glue is to use an acetone-based nail polish remover. Apply a few drops of the remover to the surface/item and leave it for a few minutes to allow it to soften the glue bond.

If possible, you can also use a cotton swab or pad soaked in acetone to apply the remover to the surface. Once the glue is softened, gently scrape or peel away the glue using a blunt tool such as a butter knife, a solvent-resistant plastic putty knife, or an old credit card.

Once the surface is clear of glue, use a damp cloth or damp paper towel to wipe away any remaining residue. If necessary, you can use a little soap and hot water to remove any residual adhesive.