Making pleats in a valance is a fun task that can make a simple fabric look much more elegant and sophisticated. To begin, measure the desired window width, and calculate how many pleats you’ll need.
You’ll want to space the pleats evenly and create enough fabric to form the pleat, but the exact measurements will depend on how deep of a pleat you’re trying to make and how full you want the valance.
Once you’ve determined the length between each pleat, use this length to determine the pattern length of the fabric.
Next, cut two equal lengths of fabric that match the pattern length that you calculated and lay them right sides together. If desired, you can add a light interfacing to the back side of the fabric so the pleats will keep their crispness better.
Then pin the fabric with straight pins at the interval that you calculated for your desired pleated look.
Sew the pinned edges of your fabric together. Once that’s done, starting from the sewn end and working toward the open end, slide and evenly distribute each pair of pleated panels in opposite directions.
Make sure to iron the pleats as you go.
At this point, if you’re attaching the pleats directly to a mounting board, finish the edges with bias tape. Otherwise, if you’re attaching the pleats to a rod pocket heading, hand stitch the side edges of the valance.
Then sew a pocket heading on the top edge and attach it to the rod. Finally, hang your valance and enjoy the result of all your hard work!.
How do you make scalloped edge curtains?
Making scalloped edge curtains is a fairly easy task and can add a unique and stylish touch to your window treatments. To make scalloped edge curtains, you will need to begin by measuring and marking your fabric according to the desired width and length of the curtains.
When you have the measurements for the fabric, create scallops along the bottom edge of the fabric by folding the ends together and making small snips along the fold. Make sure the length of the snips and the depth of the curves are consistent.
Once you have cut all of the scallops, fold the sides inwards, and press in place. You may decide to create a hem, or you can simply leave the edges raw. Finally, use a rod pocket header to attach the curtains to your window frame.
To do this, sew along the top of the fabric, leaving an opening at the center that can accommodate your rod. Insert the rod and hang the curtains on your window.
How are pleated valances measured?
When measuring a pleated valance, the length of the valance should typically be determined along the top of the rod or the front edge of the pleat. It’s important to consider the size of the pleat that’s used to give you an accurate measurement.
Some pleated valances will have measurements taken from the top of the rod and the bottom of the pleat, others will be measured from the top of the rod and the top of the pleat. The width of the valance should be measured from the left to right end and will typically equal the rod’s size.
For instance, if the rod is 6 inches, the valance will usually be 6 inches wide as well.
Another factor to consider when measuring a pleated valance is whether it needs to overlap the window casing. If the windows are standard size and the casing doesn’t need to be filled in, then a standard-sized pleated valance should do the trick.
If the window is wider than a typical size, then the valance should be wide enough to overlap the edges of the window.
Finally, when measuring a pleated valance, the hanging style should also be taken into account. If the valance is to be hung from a rod, then the measurements should be taken from the rod to get the proper fit.
For pleated valances hung with rings or hooks, the measurements should be taken from the rings or hooks accordingly.
What is a pleated valance?
A pleated valance is a window treatment that adds style, texture, and sophistication to a room. It typically consists of a flat top panel with pleated sides that hang from drapery rods or mounting boards.
Pleated valances provide a tailored, finished look to windows, incorporating texture, softening hard lines, and adding style that creates a focal point for a room. They can be standalone pieces or layered with other window coverings, such as blinds or curtains.
Pleated valances come in a variety of materials and fabrics, from lightweight and sheer to heavy, opaque cottons and linens, in solid colors and prints. Pleated valances coordinate best with traditional or transitional decors and can create a relaxed, softly tailored look in any room.
What can I use instead of a valence?
Rather than relying solely on a valence, it is possible to use a range of alternative techniques to evaluate the emotional response to a product or service. These techniques can include surveys, interviews and observational data.
Surveys can be used to invite customers to provide opinions on the emotional response they had to an experience in question. Semi-structured interviews can be used to gain greater insight into underlying feelings, as well as allowing for probing questions to explore further more subtle responses.
Finally, observational data can be gathered by either observing directly, or by asking participants to keep a diary in order to record their emotional responses. Whatever data collection methods are used, it is important to ensure that there is a valid and reliable technique to quantify the data collected.
How much fabric do I need to make a valance?
The amount of fabric you will need to make a valance will depend on a few factors, such as the size of the window, the style of the valance, and the visibility of the fabric from different angles. Generally, a good rule of thumb is to allow for up to twice the width of the window, plus an additional 10-12 inches of extra fabric to accommodate the pattern repeats and pleats.
If your windows are larger, you may need to allow for more extra fabric than this. If you plan on hanging your valance close to the ceiling, you may need more fabric for drapery fullness. Allowing for more fabric will also allow you to hem, gather or pleat the curtains – which can create a more aesthetically pleasing look.
If you plan to make a box pleat valance, also factor in the width of the pleats. If you plan on using a patterned fabric, you will need to space out the pattern as you lay out the fabric in order to avoid mismatched lines and misplaced components.
Lastly, if the valance will be visible from both the front and the side view, it’s best to plan on using more fabric to ensure a full and finished look.
How do you make a valance out of cardboard?
Making a valance out of cardboard is a cost effective and simple way to create a custom window treatment without having to purchase expensive fabric or hardware. Here are the steps you need to take to construct your own DIY valance:
1. Choose a design. Measure the size and shape of your window to determine the size of the valance you would like to make. Sketch out your design on a piece of paper.
2. Cut out the cardboard. Use a sharp craft knife or X-Acto knife to cut the cardboard into the shape and size for your design. You may want to use a ruler to ensure the edges are straight.
3. Attach the valance. Fold your cardboard into the shape of your design and secure it together with tape or glue. If desired, you can hang it from a rod or attach it to the wall with nails or screws.
4. Paint or decorate the valance. Use spray paint, craft paint, markers, or decoupage paper to decorate your valance and make it your own.
5. Hang it. Be sure to hang the valance safely and securely. If desired, you can also create a valance liner out of fabric or felt to completely cover the cardboard valance.
That’s it! With a few simple steps, you have just created your own custom valance out of cardboard. Enjoy your handiwork!
What are the three types of valance?
The three types of valance include tailored, gathered, and head box styles. Tailored valances feature a clean-cut, straight look that is formal and contemporary. Typically there is no break or gap in the fabric as the header is usually flat and the bottom edge is usually finished with a loop, rod pocket, or jabot.
Gathered valances are more casual looking, featuring a raised header and fabric that is gathered into the header. This look is created by threading cords through the hem of the valance, which is then used to create a voluminous, luxurious look.
A head box is a type of valance that frames a window with a box like frame. It typically has a squared off shape that covers the length of the window but not the sides. The fabric hangs directly from the frame onto the sill.
Head box valances look best when paired with a window treatment such as blinds or shades, as the design will help to accentuate the window’s shape.
What is the proper length for a valance?
The proper length for a valance depends on your window size, the height of your curtains, and the desired look you are hoping to achieve. Generally, the valance should measure two to four inches above the window, but this should also be balanced with the length of your curtains.
If you plan on hanging your curtains higher than your window, typically one to two inches should be added for every six inches of space. When choosing the width for a valance, you should keep in mind the size of the window and the size of the room.
Your valance will usually measure ½ – 1/3 of the width of window. If you have a large window or plan on having a double width valance, it is best to measure the area before you buy the fabric to ensure that you get the length and width you desire.
Additionally, the end of the valance can either be a straight edge or curved, creating a different look. The shape of the valance you choose will also help determine the length and feel of the look.
How deep should valances be?
Valances can be hung at a number of different depths depending on the interior decor style and desired look. Generally, if the main purpose of the valance is purely decorative, then it should be positioned 1″ to 3″ above the top of the window.
In contrast, when the valance is used as a window treatment to manage light and privacy, it should come approximately 4″ to 6″ above the top of the window. Depending on the window size, you may opt for a deeper valance and hang it 8″ or more above the top of the window frame.
While the size of the valance plays a role in the overall look and feel of a room, the depth of the valance is also important in terms of the functionality. With a shallow valance, it can provide little to no coverage, but with a deeper valance, more light and privacy can be achieved.
Ultimately, the depth of a valance can vary from room to room and should be considered in relation to the aesthetic and desired functionality of the window.
How long should a valance be for a 72 inch window?
The length of the valance for a 72 inch window depends on several factors, including the size and shape of the window, the design of the room, and the desired look. Generally, the valance should be at least one-half the width of the window and no more than two-thirds the width of the window to look proportionate.
You may want to opt for a longer valance if you want to add more dimension and texture to the room. In most cases, it would be appropriate to hang the valance between 36 and 48 inches in length for a 72 inch window.
How tall is a standard valance?
A standard valance typically ranges from 12-20 inches, depending on the size of the window and whether you choose a flat or scalloped valance. Measure your window to determine the length you will need.
The width of a valance is typically 1.5 – 2 times the width of the window. When measuring for a valance, always measure twice for accuracy and consider any obstacles that may interfere, such as window handles, curtains rods, etc.
as these can affect the look and fit of your valance.
What is the shortest valance length?
The shortest valance length is typically 4 to 7 inches. Valances, which are a type of window treatment, come in all sorts of lengths. Generally, though, shorter valances serve to give more of a modern, minimal look, while longer lengths are more traditional.
The actual length of the valance will vary depending on the décor, size of the window, and the type of rod being used, but the typical minimum length is 4 to 7 inches.
