Skip to Content

How do you shorten a chainsaw chain?

In order to shorten a chainsaw chain, you will need a few tools. These include a chainsaw chain rivet tool, a vise, bolts and a screwdriver.

Begin by preparing the chainsaw chain for shortening; start by making sure the chain is clean and dry, and that the tensioner is backed off so that the chain is loose. Place the chain in a vise and secure it in place.

Then, select the rivet that is one link shorter than your desired length, and hold it in place with a screwdriver. Use the chainsaw chain rivet tool to press the rivet into place. Repeat this process until all of the links have been removed.

Finally, retighten the tensioner to ensure that the chain is properly tensioned. As long as the rivets have been pinched properly, your chain should now be properly shortened.

Can a chain be shortened?

Yes, it is possible to shorten a chain. Depending on the type of chain, the procedure will vary. Generally, the chain should be moved to a vise in order to hold it in place while being worked on. The excess links should then be cut off with a pair of bolt cutters or similar.

Once the excess links have been removed, a chain breaker tool will be needed to remove the connecting pins in each link. The removed pins should then be replaced to connect the two remaining ends of the chain together.

After checking for smooth links, the shortened chain should be ready for use.

Can a link be taken out of a chainsaw chain?

Yes, a link can be taken out of a chainsaw chain. This is usually done to shorten the chain or to replace a worn or damaged link. The process for taking out a link typically involves the use of a chain breaker tool, which is designed to pull the chain apart, allowing you to remove the chain from the saw.

Once the chain is out of the saw, you would insert the chain breaker’s pin into a hole in the link and push it until the link is pushed out. It is important to note that the chain should be tightly tensioned when performing this task in order to prevent any damage to the chain or the saw.

Additionally, you should follow the instructions carefully and take care to not apply too much pressure, as this might damage the link or weaken its strength. Once the link is out, you can use a file or a grinder to clean any rough edges on the chain.

What do you do with a stretched chainsaw chain?

If you notice that your chainsaw chain is stretched, you need to address the matter in order to maintain the safety and integrity of the chainsaw and its components. The first thing to check is the tensioner and associated components to ensure they are all properly secure and working in tandem.

If there is an issue with the tensioner, it can often be adjusted to bring the chain back to its original tension.

If the tensioner is not the cause of the stretching, then it is likely that the chain has worn out, and should be replaced. When inspecting any chain for wear, you should pay particular attention to the cutting teeth, as well as the drive links and the rivets, to identify any signs of wear.

If all of the above look to be in good condition, the sprocket needs to be checked and replaced if necessary. If the chain stretches to the point where new rivets must be installed, then it will require a chain breaker to get the job done.

In any case, it is important to remember that chainsaws are powerful and dangerous tools and must be treated with respect and care. A stretched chain can cause improper functioning and possible injury, so it is important to replace it promptly when necessary, as well as giving all components of the chainsaw a thorough safety check to ensure it is in proper working condition.

Why do chainsaw chains get loose?

Chainsaws are designed to be used with chains that feature a certain amount of tension. This tension helps to ensure that the chain is effectively cutting through objects. Without sufficient tension, the chain can vibrate more as it operates, resulting in reduced efficiency and an increased risk of kickback.

The tension of the chain can become loose over time as the chain gets worn out, as the bar gets worn out, or due to the fact that the sprocket and drive links can become loose. As the chain wears out and becomes shorter, it tends to loosen up more.

Generally, the chain should be checked and adjusted every time it is used, and it should be replaced at least once a year.

If the chainsaw is running for long periods of time, it can also impact the tension. As the engine runs, it can cause the chain to expand. This can cause the tension to be lost and the chain to become loose.

It is important to remember to let the engine cool off before adjusting the chain tension.

What does a rivet spinner do?

A rivet spinner is a device used to fasten two pieces of metal or other materials together. The spinner consists of a rotating drill bit which is positioned to the rivet’s surface at a 90-degree angle.

It then turns the rivet and pulls it together, creating a “cold” joint. This technique is used in many everyday items such as cars, boats, aircraft, large structures, and even small parts, due to its versatility.

The rivet spinner may be used in different industries including construction, motorsport and engineering. It is also used as an alternative to welding, as it is faster and more cost-effective. In addition to this, the joint created is highly secure and will not loosen over time.

Due to the manoeuvrability of the rivet spinner, it is also considered to be a safer option than welding.

How do you use a chain breaker tool?

Using a chain breaker tool is not difficult but you will need to take care when using it to make sure that you don’t damage the links in the chain.

First, you will need to identify which link in the chain will need to be removed. If the chain is old and rusty, it may be difficult to find the correct link. To identify it, start from the joints of the chain and move in one direction until you find the last link that hasn’t been connected yet.

Once both sides of the link have been identified, you can begin to use the chain breaker tool. Place the chain breaker over the link and make sure that the pin is positioned correctly. Tighten the knurled knob firmly, but be careful not to over-tighten it.

Next, turn the handle slowly to push the pin out of the link. As the pin is being pushed out, make sure to pull the link slightly apart so that it doesn’t get stuck in the chain. Once the pin is completely removed, the link can be easily removed.

Finally, once the link is removed, the chain can be reattached. Place the link back in the chain and make sure that the joint is correctly aligned. Push the pin back into place and use a pair of pliers to crimp the pin if necessary.

Using a chain breaker tool is essential for maintaining and changing bicycle chains. With the correct tools and knowledge, you can easily break and reattach bicycle chain links.

What happens if the chain is too tight on a chainsaw?

If the chain on a chainsaw is too tight, it can cause a number of problems. The chain can overheat, causing it to stretch and wear out prematurely. This can also cause the chain to jam, resulting in slower cutting performance.

Additionally, tightening the chain too much can cause the saw’s drive to slip and be less efficient, and the saw may vibrate more than normal due to the extra tension on the chain. Finally, a tight chain can cause the saw to be more difficult to operate and may even cause it to kickback more than normal, which can be dangerous.

It is important to maintain the chain’s tension correctly to ensure safe and efficient operation and to prevent premature wear.

Why does my chainsaw smoke when cutting?

Chainsaws can smoke when cutting for a variety of reasons. If the chainsaw is new, it may just be the normal expected smoke generated by the running motor and hot exhaust pipes. However, if the chainsaw is older, the increased smoke could be indicative of a more serious problem.

It is possible that the chainsaw is running too rich, meaning that it is consuming too much fuel relative to the amount of air it is ingesting. This is usually caused by a problem with the carburetor and may require adjustment or servicing.

Another potential cause of the smoke could be problems with the spark plug. It may be too hot or cold, which could lead to incomplete combustion of the fuel and the creation of smoke. In either of these cases, it is advisable to have the chainsaw serviced by a professional in order to reach a proper diagnosis and repair the issue.

Without doing so, the chainsaw can become a fire hazard and be dangerous to operate.

When should you throw away a chainsaw chain?

It’s important to inspect your chainsaw chain regularly for signs of wear and tear, including chips, rounded cutter teeth, and broken parts. If any of these signs of damage are apparent, your chainsaw chain should be replaced immediately.

Additionally, if your chain has gone too long without sharpening or if it has been exposed to a lot of wear and tear from heavy-duty use, it should be replaced. It’s also important to replace your chain after a certain amount of time, typically around 3 to 5 years from the date of purchase, as your chain may have become dull from regular use even if it appears to be in good condition.

Finally, if you are planning to perform heavy-duty tasks with your chainsaw, it’s important to upgrade your chain to one with a higher gauge and more cutting teeth, which can better handle heavier tasks.

Why won’t my chainsaw cut straight?

Chainsaws are designed to cut straight, but there are many reasons why yours may be struggling to do so. The chainsaw chain may not be properly adjusted, or the chain may be worn, which can cause the saw to wander and cut unevenly.

The chain also needs to be properly maintained; dull chains move slower and that can cause them to cut crooked. The guide bar or chain may also be bent, out of alignment, or warped due to wear or improper maintenance.

In addition, the engine power may be too high, making it overly powerful, causing the chainsaw to buck. Finally, you may be pushing too hard while cutting, causing the saw to twist and cutting crookedly.

To ensure that your chainsaw is cutting straight, check the chain pressure and tension, sharpen or replace the chain, adjust the engine power as needed, and make sure to be gentle as you’re cutting.

How tight does a chainsaw chain need to be?

A chainsaw chain needs to be tensioned to the manufacturer’s recommendations, which is typically just tight enough to hold the chain in contact with the bar, but not so tight that the drive links can’t move.

To tension the chain, use the tensioning screw or nut on the side of the saw, which can generally be accessed from the outside of the saw handle. When properly tensioned, most chains will not come off the saw without the user manually removing it.

If the chain has too much tension it can cause the chain to skip or jump, while too little tension will cause the chain to be ineffective and unsafe to use. It’s important to check the tension frequently during use, as the chain can become loose as the bar and chain wear down, especially when cutting harder material.

Can a chainsaw chain stretch too much?

Yes, a chainsaw chain can stretch too much. Over time, the chain’s components can become worn out, which causes them to stretch. When the chain is stretched, the guide bar’s groove becomes increasingly larger, making it difficult for the chain to fit properly.

This causes the saw to run inefficiently since the chain is being forced to fit in the guide bar. The saw can vibrate excessively, which can create damage to the other components of the saw. Additionally, when the chain is excessively stretched, it experiences more give and the chain links can actually become detached from the saw during use.

This can create a dangerous situation and can cause serious injury. It is important to regularly inspect and adjust the chain tension so that it does not become too loose or too tight.