Starting a Genie boom lift begins with safely positioning the lift on firm, level ground, with the feet of the outriggers evenly extended and the platform hoisted clear of any obstructions. Once the lift is in position, the operator should then rotate the power switch to the “on” position.
Depending on the model, the operator must then depress a lift/lower lever/foot pedal to engage the hydraulic drive motor and lower the platform. The machine should also be provided with an emergency disconnect switch, which, when activated, will immediately stop the drive motor.
Once the platform has been lowered, the operator should check to ensure that the boom is correctly positioned and that the boom arm and jib are in the down and stowed positions, respectively. Once these steps have been taken, the operator should ensure the all persons in the vicinity are clear, and that the outriggers and stabilizers are properly locked in place.
The operator can then begin the climb to height by activating the lift/lower lever/foot pedal and engaging the hydraulic drive motor. The operator should raise the boom arm and jib as needed until the work platform is at the desired height.
At this point, the operator should check to ensure the lift is positioned and levelled before proceeding.
If any movements and adjustments are required, the operator should lower the platform, adjust the lift as necessary, and then raise the platform back to the desired height. Once the platform is at the desired height and position, the operator should check that all necessary safety systems are engaged and deactivate the lift/lower lever/foot pedal.
The boom lift is then ready for use.
What does Ch mean on Genie lift?
The abbreviation “Ch” on a Genie Lift refers to the “Capacity Hydraulic” system. This system enables the Genie lift to safely and easily lift heavy loads. The Capacity Hydraulic system works by using hydraulic pressure to raise and lower the lift platform.
This system also includes safety features such as a mechanical locking system and an anti-sway system to ensure that the load remains secure during operation. The hydraulic system also provides improved stability and smooth operation, which is why Genie recommends it for heavy loads.
Which button do you press on a lift?
In order to operate a lift, you will need to press either the floor number button with the corresponding floor number or the “open”/”close” button, depending on the type of lift. For a standard lift, you will see a panel of buttons with all the floor numbers inside the lift.
You simply press the correct number and the lift will travel to that level.
If you have a modern lift, then you’ll need to press the “Open” or “Close” button in order to open and close the lift’s doors. Once the doors are open, you can then press the floor number button corresponding to the floor you want to go to.
The lift will then take you to that floor.
It is important to remember that you should always press the “close” button once you have selected the floor you wish to go to, otherwise the doors may remain open and the lift will not move.
How do you use a lift step by step?
Using a lift is fairly straightforward and can be accomplished in the following steps:
1. Before attempting to use the lift, read the operating instructions and any safety precautions included with the lift. Make sure all safety features, such as the safety latch and locking mechanism, are properly engaged.
2. Ensure that the lift is positioned properly and that the arm is firmly anchored to the lift platform.
3. Take your position on the platform, setting any materials that need to be moved within easy reach on the platform.
4. Press the appropriate lift button or lever to raise the lift platform to the desired level.
5. When the platform has reached the desired level, release the lift button or lever and stand safely on the platform.
6. Use the corresponding lift buttons or levers to move the platform in the desired direction.
7. When the platform has reached its final destination, press the lift button or lever to lower the platform.
8. When the platform has reached the ground, release the lift button or lever and exit the platform.
9. Lower the arm of the lift and disengage any safety features, such as the safety latch and locking mechanism, before leaving the lift unattended.
Following the above steps will ensure a safe and efficient use of a lift.
How does a lift button work?
A lift button is a device that allows users to activate the lift to their desired floor. When the button is pressed, the lift responds by moving to the designated floor. The button is connected to an electrical circuit and a set of wires, which will cause the lift to respond when activated.
This is done by either sending a signal through a set of relays or by directly controlling the motor that powers the lift.
The button contains a switch or tactile switch, which is a device that changes its electrical resistance when pressed. This allows the button tosend out a signal in the form of electrical current. The electrical current then travels down a set of wires to an electrical component called a relay.
The relay will open and close electrical circuits, which will cause the motor that powers the lift to start moving.
When the lift arrives at the designated floor, the relay will deactivate, sending a signal to a braking system which will stop the lift from continuing to move. Finally, when the desired floor is reached, the lift’s doors will open and the user can enter or exit the lift.
How much does a 65 foot Genie lift weight?
The maximum lifting capacity for a Genie 65 foot Boom Lift will depend on the specific model in question. Genie offers a range of Boom Lifts that can lift up to 500 lbs, 1,000 lbs, 2,000 lbs, or 4,000 lbs.
For other Genie models, the weight capacity might be lower. It is important to refer to the operator’s manual specific to the model of Boom Lift to determine the exact weight capacity. Additionally, the weight capacity is reduced when the platform is fully extended or when the boom is at an acute or obtuse angle, and can also be affected by wind and other environmental conditions, so it is important to use caution when operating a Genie Boom Lift.
How high does a Genie boom go?
A Genie boom lift can reach up to 125 feet in height. It has a maximum lift capacity of up to 500 pounds and can extend out nearly 40 feet horizontally. It’s important to note that some Genie models may have slightly different specs, so it’s important to double-check the specifications for your particular model before attempting to reach the maximum lift height.
Safety should always be the primary priority when operating a Genie boom lift – along with making sure you comply with all relevant local, regional and industry safety regulations.
How heavy are boom lifts?
The weight of a boom lift will vary greatly, depending on the size, model and manufacturer of the lift. Generally, small battery operated lifts or electric scissor lifts will range between 500 and 5,000 pounds.
Larger, gas-powered and lift models may range from 6,000 to 15,000 pounds or more — with trailer mounted and telescopic boom lifts weighing even more. The total weight of a lift will also vary according to the accessories and attachments that are used on the model.
It is important to pay attention to the weight limits on the lift, as exceeding that limit could result in an unsafe operation.
What’s the longest boom lift?
The longest boom lift currently on the market is the JLG Ultra Boom, which can reach heights of up to 261 feet. This lift is designed for use in demanding, high-reach applications and is a four-section, full-power telescopic boom lift that has an up-and-over clearance of more than 100 feet.
It also features a single, continuous boom bundle with a vertical jib and extension boom for greater outreach and superior platform positioning. Other notable features include traction drive, oscillating axles, positive traction control, and hydraulically driven outriggers.
It is perfect for large outdoor applications, high-up lighting and installation projects, maintenance, and other tasks that require long reaches.
Can a boom lift tip over?
Yes, a boom lift can tip over if certain precautions are not taken. Several factors can cause a boom lift to tip over such as: uneven ground, lifting high and off balance loads, wind gusts, and incorrect operation.
It is important to read and understand the manufacturer’s instructions and be sure to properly prepare the job site before using the boom lift. Make sure the ground is flat, level, and firm and that the outriggers are firmly placed on the ground and fully extended.
Ensure that the lift is never operated beyond its rated capacity and not overloaded with materials. Be aware of weather conditions, especially wind gusts, which can affect the stability of the lift. Additionally, operators must remain inside the basket at all times, and be aware of their surroundings.
Taking all the necessary safety precautions will help to ensure that the boom lift does not tip over.
Where are Genie lifts manufactured?
Genie lifts are manufactured by the Manitou Group, a global leader in forklifts, aerial work platforms, material handling and warehousing equipment. The Genie brand is manufactured in the United States, France, China, Brazil and Germany and specializes in product innovation, providing safe, efficient and intuitive materials handling solutions.
Genie has several factory locations in the United States and Canada, including an 82,000 square foot manufacturing facility in Redmond, Washington, where all Genie lifts are engineered, designed and manufactured to the highest standards of quality.
Manitou has a global network of expert dealers, highly-trained service technicians, and dedicated after-sales support teams.
Who makes Genie lift?
Genie lift is a brand of aerial work platforms and material lifts manufactured by Terex Corporation. Terex Corporation is an American global manufacturer of lifting and material processing products and services.
The company manufactures a comprehensive range of products for a variety of industrial markets including the construction, infrastructure, services and energy, manufacturing, and aerospace and defense industries.
Genie is one of the leading brands of Terex Corporation, providing an extensive selection of aerial access solutions such as booms, vertical lifts, and scissor lifts. Genie is known for their reliable and safe products, designed with the operator in mind.
They offer their products globally, providing customers with the best possible level of service available.
What is a Genie s60?
A Genie s60 is a self-propelled lift designed for general construction and industrial maintenance use. It is a three-wheeled boom lift with a panoramic boom that provides 360° continuous smooth rotation.
This four-wheel drive unit has an extendable outrigger system and can reach working heights of up to 60 feet. The Genie s60 offers a large working envelope, high capacity, and a wide variety of features, providing an optimal working environment while allowing workers to be safely lifted to their work spot.
It includes unique jib, lanyard, and tool connectors to enable the operator to easily access the desired operating level, which allows for increased productivity and safety. The Genie s60 also includes a stabilizer sensor and Smart Link™ JIB Management System for convenience and safety.
It also has an optional brushless motor and AC power to ensure reliability and provide operator comfort in any environment.