To take apart a trimmer head, the first step is to make sure your trimmer is powered off and unplugged. Safety first! Next, take off any guard or cover that is covering the trimmer head. Then, unscrew the screws or nuts that are holding the trimmer head in place.
Depending on the make/model, you might need to use a small wrench or a screwdriver. Once the screws/nuts are undone, the trimmer head should simply pull off. If it doesn’t come off easily, you can gently tap the trimmer head handle against the ground to loosen the head.
With the trimmer head now removed from the trimmer, a simple tug should take apart the components of the head itself. Be sure to examine all the components and make sure everything is in good condition before you reassemble the head.
How do you change the head on a WORX trimmer?
Changing the head on a WORX trimmer is a relatively simple process. To begin, find the release button on the side of the trimmer head and press it. This will allow the head to be separated from the trimmer body.
Next, select the new trimmer head you wish to utilize then align it with the shaft. Push the head onto the shaft until it clicks and locks into place. Lastly, press the release button to securely tighten the head to the shaft and your trimmer is ready for use.
Note that depending on the type of trimmer head and trimmer model, the release button’s position and shape may vary. If you have any difficulty ensuring that the head is securely fastened, refer to the trimmer manual for more detailed instructions.
How long does a WORX trimmer last?
The lifespan of a WORX trimmer is hard to determine without knowing the model, as different trimmers will vary in how long they remain in working condition. Generally speaking, WORX trimmers are made with quality parts and can last for several years.
With the proper maintenance and care, a WORX trimmer is capable of lasting for a considerable amount of time.
For most WORX trimmers, it’s important to make sure the cutting head has been properly lubricated prior to use, and that the trimmer has been regularly cleaned and stored properly. This will help keep the trimmer in good working condition and potentially increase its lifespan.
Additionally, regularly checking for any loose connections or parts that need to be tightened can also help increase the longevity of the trimmer. Ultimately, the life span of a WORX trimmer will depend on how well it is maintained throughout its life.
Why did my Worx trimmer stopped working?
There could be a few reasons your Worx trimmer stopped working. Firstly, make sure the fuel tank is full and the oil-to-gas ratio is correct. If that does not resolve the issue, check to see if the spark plug is in working order and the ignition switch is correctly in place.
If that does not resolve the problem, you can try checking the air filter and spark arrestor for blockages or clogs. If those do not resolve the issue, it could be a problem with the carburetor, which will have to be replaced.
Lastly, it could be a problem with the electrical components of the trimmer; such as the wiring, battery, coils, or stator. If any of these problems occur, it is recommended to seek professional help to make sure it is fixed properly and safely.
How do I fix my lawn trimmer?
Fixing your lawn trimmer depends on the specific problem that you’re experiencing. Before you begin any steps to repair your lawn trimmer, you should wear safety glasses and gloves, and make sure the trimmer is turned off.
With safety in mind, the first step to fixing a lawn trimmer is to diagnose the issue, which can range from carburetor problems to fouled spark plugs to issues with the fuel or air filters.
If you are having issues with starting your lawn trimmer, you should begin by checking the fuel and air filters for any blockages or debris, and replace them if necessary. You should also verify that there is sufficient gasoline in the tank, that the spark plug has been properly gapped, and that the carburetor has the right mixture of fuel and air.
If any of these parts appear worn or damaged, they should be replaced before attempting to start the lawn trimmer.
If your lawn trimmer is running but not producing power, you may need to check the blade as it may be dull or damaged. If it appears to be in good condition, you may need to clean out the spark plug or adjust the carburetor to ensure the right air and fuel mixture.
If you are unable to diagnose and repair the lawn trimmer on your own, you may want to take it to a professional technician for repair. Depending on the issue, it may be more efficient and cost-effective to replace the lawn trimmer instead of attempting to repair it.
Can you refill Worx trimmer spool?
Yes, you can refill a Worx trimmer spool. To do this, you’ll need to purchase a Worx spool refill—which includes two 0.065-inch cutting lines—and ensure that your Worx trimmer is powered off before commencing.
Also make sure your trimmer spool is free of dirt and debris.
First, pull the spool from your Worx trimmer and carefully unspool the string. Then, cut one of the lines from the Worx trimmer to create an end. Slice the second line for about six inches, and then separate the ends.
Take the separated ends, and insert each into the slit opening at the end of the Worx trimmer spool. Then, simply wind each of the edges of the line around the spool in an opposite direction until the spool is full.
Finally, remove the ends from the slits, and press on the spool covering until it is secure. You should now be ready to use your refilled Worx trimmer spool.
Who owns Worx brand?
The Worx brand is owned by Positec Tool Corporation, a global manufacturer and distributor of electric and cordless power tools, lawn and garden tools, as well as other home and automotive products. Founded in 1994, Positec Tool Corporation is headquartered in Charlotte, North Carolina and has offices in the United States, Canada, France, and the United Kingdom.
Positec Tool Corporation specializes in the production of its own brands, including Worx, Rockwell, and Wolfcraft. Positec Tool Corporation is committed to developing innovative products that are easy to use and of utmost quality.
Additionally, Positec Tool Corporation emphasizes customer service and support with a variety of tools and resources available on their website.
How do you use a Worx electric edger?
Using a Worx Electric Edger is easy and enjoyable. Before use, ensure you have the proper safety equipment including goggles and gloves. Additionally, inspect the electric edger for any signs of damage.
To begin, ensure the edger is plugged into a designated, outdoor electrical socket. Now, press the safety switch located at the top of the handle to turn on the appliance. The cutting wheel will start spinning.
For best results, make sure the edger is fully charged and always use a sharp, new blade.
To use the edger, start at the edge of your sidewalk and make a pass from one end to the other. Ensure the wheel is kept at its highest point when you start, and gradually lower it as you roll forwards.
Make sure the blade is kept between two and three inches deep in the ground.
Depending on your land, slow down as you approach sections with rocks, tree roots, and other obstacles. When finished, push the safety switch located at the top of the handle to turn the appliance off.
Finally, use a rake, spade, or other tool to clear away any remaining dirt or grass clippings.
How long does it take to charge a 20 volt Worx battery?
It will generally take roughly 4-5 hours to fully charge a 20-volt WORX battery. However, the amount of time it takes to charge a WORX battery could vary depending on the battery’s specifications, the charger’s output, and other factors, such as the battery’s age and condition.
For best results, always use an official WORX charger when attempting to recharge your battery. Additionally, it’s important to remember that when charging a battery for the first time, or after a long period of inactivity, do not attempt to charge it for any longer than three hours total.
Why is my Weedwacker not starting?
Depending on the make and model of your Weedwacker, the answer to why it’s not starting could be one of many different things. It could be due to a faulty spark plug, an insufficient fuel/air mixture, or a carburetor that needs servicing.
It could also be caused by a clogged air filter, or dirt buildup in the carburetor or fuel line. Other potential causes of a Weedwacker not starting include faulty fuel lines, a damaged pull cord, or a bad spark plug lead.
It’s best to reference your manual to narrow down the possible diagnoses, or take the Weedwacker to a qualified mechanic for further inspection. A basic troubleshooting procedure can help you identify the root cause of your Weedwacker not starting.
To begin, inspect the spark plug for cracks and evaluate the color of the spark plug’s electrodes. A dark color indicates that your spark plug has been exposed to too much heat, and needs to be replaced.
Additionally, inspect the fuel level and condition of the fuel/oil mixture. If the mixture is old or low, you should replace it with fresh fuel.
If the engine turns over but won’t start, the air filter may be clogged and need to be cleaned. Additionally, you should check if the ignition switch is functioning correctly, if the fuel filter is clogged, or if the fuel line has kinks in it.
After ensuring that these components are working properly, you should clear the carburetor. To do this, remove the carburetor bowl and clean the outside of the bowl with a rag. If you don’t see any dirt buildup, then the issue could be with the internal components of the carburetor and it should be professionally serviced.
If all of these troubleshooting steps fail, the Weedwacker may have to be sent to a professional repair center to be inspected further and possibly repaired.
Why does my trimmer keep shutting off?
There could be a few different causes for why your trimmer is shutting off, each of which would require different forms of troubleshooting.
The first possibility is that your trimmer is getting too hot. Trimmers rely on motors which heat up as they run, so it’s important to make sure that they don’t overheat by providing adequate ventilation and breaks between use.
If it’s possible, try to use the trimmer in a less restrictive and cooler area, give it more breaks between use, and avoid running it for too long consecutively.
Another possibility could be a fault in the electrical connection of the trimmer. This could be due to a loose wire or a worn plug, which may need to be reinforced or replaced. Check the wiring and connections of your trimmer, and check the plug wires are firmly connected.
If you need to replace the plug or any wiring, it’s best to seek help from a qualified electrician or trimmer mechanic.
It could also be the case that your trimmer is clogged and unable to run properly. If your trimmer has built up too much debris, it will struggle to get enough air and won’t be able to run reliably. Make sure to keep your trimmer clean and free from clogs, and to check it frequently for any buildup.
Finally, it could be a problem with the trimmer’s motor itself. If the motor is damaged or worn, it might be struggling to run and shutting down as a result. In this case, it’s likely that the motor will need to be replaced.
If you think that this is the cause of your issue, it’s best to take your trimmer to a qualified trimmer mechanic or repair shop.
Why does my trimmer dies when I give it gas?
It is possible that there are several reasons why your trimmer might die when you give it gas. The most common reason is likely related to the spark plug. If the spark plug is old or worn out, it may not be firing correctly, causing the trimmer to die when you give it gas.
Another possibility is a dirty or blocked carburetor. The carburetor controls the fuel and air mixture going into the trimmer, so if it’s blocked or dirty it won’t be able to mix the fuel and air correctly, causing it to die when you give it gas.
Additionally, you may want to check the fuel filter and the air filter, as they may be blocked or dirty, preventing the trimmer from getting the proper fuel and air mixture. Finally, if all of the above have been checked and are in working order, it is possible that the trimmer’s fuel line is clogged or has a leak, preventing it from getting the necessary fuel and air mixture to run efficiently.