Skip to Content

How often should you change Weed Eater oil?

Weed Eater oil should be changed every season, or after about 20-25 hours of running time. If you use your Weed Eater frequently, you should check the oil level every 5 hours of running and top it off as necessary.

Make sure to use fresh oil that is specifically designed for two-cycle engines. Most two-cycle engines require a mix of gasoline and two-cycle engine oil for fuel. The mix ratio of gas to oil is typically 40:1, which means 40 parts gasoline to 1 part engine oil.

To ensure correct lubrication, it’s important to use the right type of oil in the correct mix ratio. When changing the oil, make sure to drain the old oil completely and refill with fresh oil.

How do you maintain a Weed Eater?

Maintaining a Weed Eater involves several steps, such as:

1. Changing the oil: Changing the oil in your Weed Eater every 25 hours of usage will help prolong the life of the machine. When adding new oil, use a mediump-weight oil suited for 2-cycle engines.

2. Replacing Spark plugs: Depending on the amount of use, it is recommended to replace the spark plugs every year. When replacing the spark plugs, be sure to use the ones specified by the manufacturer.

3. Cleaning the air filter: The air filter of your Weed Eater should be cleaned regularly to help the machine run more efficiently. When cleaning the filter, remove all dirt and debris using a soft, damp cloth.

4. Checking and replacing fuel lines: Take the time to check the fuel lines once in awhile to make sure they are not cracked or damaged. If they are found to be damaged, replace them right away.

5. Sharpen the blades: Regularly sharpen the blades of your Weed Eater. Doing this will help it work more effectively, and will make the job easier.

Taking the time to properly maintain your Weed Eater will help ensure it runs effectively for years to come.

How do you service a string trimmer?

Servicing a string trimmer requires some basic maintenance to make sure it’s in top condition for a successful cutting season. Here’s a basic rundown of how you can service your string trimmer:

1. Change the string trimmer line. Check the line regularly, especially after a few hours of use. If the line is fraying or worn out then it should be replaced. You can do this by cutting off the existing line and winding in a new spool of trimmer line.

2. Clean and sharpen the blade. Make sure to use a wire brush and sharpening stone to remove any dirt, grime or rust and sharpen the edge of the blade. This ensures your trimmer is cutting through weeds and grass smoothly.

3. Change the oil. Check your owner’s manual to see how often you should change the oil in your string trimmer. Make sure to use the right type and quantity of oil to keep your trimmer running well.

4. Check and clean the air filter. The air filter helps to keep dust and debris out of the engine and should be checked regularly to ensure it’s clean. If the filter is clogged or dirty then you should either clean it or replace it.

5. Check the fuel lines. Visually check the fuel lines and hoses to make sure they’re in good condition. If any lines are cracked, brittle or leaking then they should be replaced.

By following these steps, you can help ensure that your string trimmer runs smoothly and efficiently. Additionally, you should make sure to store your string trimmer in a clean, dry place away from extreme temperatures and moisture.

How good is lithium grease?

Lithium grease is an excellent lubricant that offers great protection against rust, corrosion and oxidation. It is blended with a high-quality mineral oil and lithium soap base that provides good adhesion and a thick, tenacious film that clings to metal surfaces.

It is water repellent and can handle temperature ranges between -45° Celsius to 120° Celsius. This makes it great for a variety of uses, such as automotive components, machinery, levers, slides, locks and other parts that are subject to heavy wear and tear.

Additionally, lithium grease releases its lubricity slowly, thereby providing long-term lubrication and greater protection for parts. It also resists dilution or compression and is great for multi-purpose applications.

Overall, lithium grease is an excellent choice for lubrication and protection, providing reliable performance and lasting durability.

What type of grease is Stihl grease?

Stihl grease is a multi-purpose, specially formulated lubricant designed for use on Stihl power tools, including chainsaws, trimmers, blowers and more. It is a high-grade, petroleum-based grease with a special anti-fling additive that prevents fling-off from rotating parts such as chainsaw sprockets and trimmer shafts.

Stihl grease is also formulated with EP (extreme pressure) additives that help protect components from extreme wear and provide longer service life. It can withstand extremely high temperatures, making it ideal for use during heavy-duty operations in harsh environments.

It is also moisture and corrosion resistant and can be used to lubricate other machinery as well.

What grease should I use for gears?

The type of grease you should use for gears in your machine will depend on the type of machine, environmental conditions and the type of motion that the gears need to handle. Generally, a universal lubricant with EP (extreme pressure) additives is suitable for most gears.

Some examples include EP grease, multipurpose lithium grease, multi-purpose lithium complex grease, and grease for enclosed gears. For more severe applications such as high temperature, high-speed and overload, other types of grease such as synthetic lubricants may be necessary.

In any event, the best advice is to consult the instruction manual of your machine to determine the best specific type of grease for the job.

How do you make weed eater strings last longer?

To make weed eater strings last longer, it is important to follow a few maintenance tips. First, inspect the strings for any signs of wear and tear. If any signs of damage are visible, replace the strings with new ones.

It is also important to check the cutting head for any wear as that can reduce the life of the strings. Additionally, you should make sure that you’re using the proper trimming technique and that you’re using the strings at the correct length to get the job done.

When installing new strings, it’s important to ensure that they are pre-cut at the correct length and that the cutting head is secured properly. Finally, try to stay away from tough objects such as rocks, gravel and cement walkways as these can cause extreme damage to the strings.

Following these tips will help ensure that your strings last longer and that your weed eater works more efficiently.

Does trimmer line get brittle with age?

Yes, trimmer line does get brittle with age. Trimmer line is typically made of nylon or plastic, both of which are susceptible to deterioration due to extended exposure to the elements. Over time, the molecules in the line may break down, causing it to become brittle, dry, and more prone to snapping when under tension.

The length of time this takes will depend on the type of trimmer line being used, the environment in which it is used, and the amount of use it sees. If you are using your trimmer regularly, it is important to check the line often to ensure it is still in good condition.

If it is getting brittle or seems to snap when under tension, it is likely time to replace it.

Does a weed wacker run out of string?

Yes, a weed wacker can run out of string. The string is wound onto a housing within the weed wacker, much like the bobbin inside a sewing machine. As the weed whacker is used, it will gradually wear away the string, and eventually it will run out.

Most weed whackers come with a handy string spool that can be loaded onto the housing so the device can be used for an extended period. It is important to remember to check the level of string every time you use your weed whacker, and to replace the string when necessary.

How much string do you put in a weed eater?

The amount of string required for a weed eater can vary depending on the model, but generally it is recommended that you put at least 15 feet of line. It is also important to secure each end of the line at one of the spool’s flanges, with the line going around the spool in the direction of the arrow.

After you thread the line, turn the spool to the “T” position, hold the ends of the lines, and pull about 6 to 8 inches of line out of the trimmer head. This will ensure the line is tight and secure.

If there is excess line, cut off the excess and make sure the ends are even. It is important to always replace any worn or broken line before you start your trimmer.

Why does my trimmer use so much line?

The amount of line your trimmer uses is largely dependent on how often you use it and how well you maintain it. If you use your trimmer frequently, or it is used on an area with thick grass or weeds, it is likely to use more line.

In addition, an old, worn out trimmer head or blunt trimmer line can cause the trimmer to use more line by not cutting properly. Lastly, the size and length of the trimmer line affects how much it is used.

If you are using a line that is too large or too long, your trimmer will use more of it then if you were using a shorter, thinner line. By keeping your trimmer head in good repair and using the proper size and length of line, you should be able to reduce how much line your trimmer uses.

How does automatic feed string trimmer work?

An automatic feed string trimmer is a lawn maintenance tool which is used to trim the edges of grass, removing any overgrowth and creating perfectly manicured edges. This particular type of trimmer is powered by electricity, so you don’t need to worry about refueling or recharging a battery.

This type of trimmer has a spinning string which is wrapped around the spool and is released by a spring-fed mechanism. As the machine is operated, the string is drawn and released at a rapid speed. This allows the trimmer to cut through dense patches of grass quickly without getting stuck.

As the string wears out, more is released from the spool. This ensures that you always have fresh, sharp string while trimming, giving you better results. Automatic feed string trimmers are usually lighter in weight than their petrol-powered counterparts, making them easier to maneuver around the yard.

They’re also a lot quieter and don’t require you to mix fuel when filling. This makes them a great choice for someone who wants an efficient and hassle-free way of trimming their lawn.

Can my weed wacker get rained on?

Yes, your weed wacker can get rained on, however it is best to avoid prolonged exposure. Water can cause rust, weaken seals, and corrode electrical components, making your weed wacker less reliable. If your weed wacker is not waterproof, you may also experience power fluctuations due to water contacting the spark plug or engine, leading to decreased performance or a potential failure of the unit.

To best avoid water damage, cover your weed wacker with a waterproof tarp or store it in a protected location when not in use. If your weed wacker does get rained on, make sure to allow it to dry completely before using again.

Can you store electric weed eater outside?

Yes, you can store electric weed eaters outside. Depending on the climate you live in, however, it’s important to make sure you provide adequate protection from the elements. If you have a shed to store it in, the ideal option is to keep it sealed away in a dry, dark location with good ventilation.

If outdoors, ensure the weed eater has a waterproof cover to prevent rain and dust from entering the motor, and make sure to store the device on a flat surface away from grass and vegetation. Additionally, be sure to disconnect the power cord and store it separately, as the cord can suffer wear and tear from extreme temperatures if left exposed.

Additionally, for best results, take the time to empty the fuel tank before storage to prevent any sign of deterioration. Regularly checking the condition of the weed eater and its cords is also a must.

Can I leave my electric lawn mower outside?

No, you should not leave your electric lawn mower outside for an extended period of time. Exposure to the elements can lead to rust, corrosion, and overall damage to any electric lawn mowers. Even if the electric lawn mower is in a waterproof covering, water can eventually get through and affect the motor or other components of the device.

Additionally, if the electric lawn mower is left in extreme temperatures, it can cause warping of the internal components. To help maintain your electric lawn mower, it is best to keep it in a dry, well-ventilated place such as a shed or garage.

Doing so can help preserve the condition of your electric lawn mower, thereby ensuring it operates at its peak performance and lasts longer.

Is it OK to hang weed eater upside down?

No, it is generally not recommended to hang a weed eater upside down. This is because the oil in the engine will run out of the crank case, and gravity can pull the oil into the air filter. This can lead to premature engine failure due to insufficient lubrication.

Additionally, the string trimmer head may also become damaged from being hung upside down. For correct storage, it is best to hang the weed eater on a hook or in an up-right position so that the motor is not under too much pressure or strain.

How should weed eaters be stored?

When storing a weed eater it is important to take the necessary steps in order to ensure that it remains in optimal working condition.

To begin, it is recommended to inspect the machine for any dirt and debris that may have accumulated during use. Once the weed eater has been cleared of any debris, the next step is to fill the tank with clean fuel, free of any dirt and debris, and add a fuel stabilizer to prevent fuel deterioration over a prolonged period of storage.

Following that, the air filter should be removed and either cleaned or replaced with a new one, depending on its condition.

To store the weed eater, ensure that it is located in an area that is well ventilated, dry, and out of direct sunlight. It is also important to protect the machine from moisture, dust, and other airborne contaminants.

If storing the weed eater indoors, use a dust cover to protect it from dust and contaminants.

Finally, it is recommended to run the weed eater for a few minutes, once a month, during its storage to keep the oil lubricating and prevent a build up of moisture and dirt on the spark plug. If the spark plug needs to be cleaned, use a clean cloth and rubbing alcohol to wipe it off.

By following these storage steps, your weed eater will remain in optimal working condition and provide many years of reliable use.

How do you store a weed wacker for winter?

Storing a weed wacker for winter involves taking certain precautions to ensure that it is well cared for and ready to use in the spring. The first step is to clean the tool thoroughly, removing any debris and dirt, and drying it off.

Once the weed wacker is clean and dry, you should lubricate any exposed metal surfaces, paying special attention to the blades, to prevent rust. Once lubricated, the weed wacker should be stored in a cool, dry place away from direct sunlight.

Make sure to cover the weed wacker with a protective cover or tarp to prevent dust and dirt from settling onto the tool. Finally, ensure that the fuel tank is empty by running the engine until it runs out, or by siphoning off any remaining fuel.

This will prevent any residue from accumulating and gumming up the tank during storage.