Olympic Waterguard Water Repellent is water-based, meaning that water is the primary component and carrier of active ingredients. It penetrates deeply into masonry surfaces to form a durable, breathable, clear waterproofing barrier against water and oil-based stains for up to 5 years on decks and up to 15 years on fences and siding.
Its advanced waterproofing technology provides excellent dirt and stain resistance, unmatched finish durability, and a clear protective barrier so your exterior masonry looks great and stays looking great by standing up to the elements.
Plus, with its low-VOC formula, it’s safe for the environment and your family.
How do you use Olympic Waterguard clear multi-surface Waterproofer?
Olympic Waterguard Clear Multi-Surface Waterproofer is a premium sealer formulated for use on interior and exterior wood, concrete, and masonry surfaces. To use it, start by making sure the surface is cleaned and free of dust, dirt, mildew, and other debris.
Next, apply a thin coat of the sealer with a brush, sprayer, or roller. Allow the sealer to dry, then apply a second coat if desired. Allow the sealer to fully cure for 24 to 48 hours before getting the surface wet.
After that, the surface will be protected from water and other damage. Clean up tools and spills with soap and warm water.
Is Olympic Waterguard good for concrete?
Olympic Waterguard is a sealer designed to protect surfaces from water and damage. It is ideal for concrete surfaces because it not only provides a shield against water, but also helps to reduce staining.
Olympic Waterguard creates a durable, breathable polymer barrier that “locks out” moisture while repelling dirt, oil and stains. It also helps to extend the life and improve the appearance of newly laid concrete, as well as safeguarding older surfaces.
Olympic Waterguard is also easy to apply – just follow the instructions and you should have full protection in a few simple steps.
What’s better than Thompson’s water Seal?
When it comes to waterproofing and protecting outdoor wood, Thompson’s Water Seal is one of the most popular options. However, there are several alternatives to Thompson’s Water Seal that offer comparable protection and performance.
One of the most sought-after alternatives is Olympic Stain. This non-toxic waterproofing solution is formulated with advanced sealant technology that offers a high level of protection against water, UV rays, and other damaging elements.
It is also known for its range of long-lasting and fade-resistant colors and finishes.
Another popular alternative to Thompson’s Water Seal is BEHR Solid Color Waterproofing Stain and Sealer. This product is also known for its advanced protection against UV rays, water, and other damaging elements.
The formulation offers superior adhesion and provides a long-lasting finish that won’t crack, peel or blister.
If you’re looking for an eco-friendly option, DEFY Extreme Wood Stain is a great choice. This wood stain is water-based and VOC-free and offers superior protection against moisture, mold, and mildew.
Unlike other formulations, DEFY Extreme Wood Stain penetrates deeply into the timber so it won’t flake, peel or blister over time.
Ultimately, when it comes to finding an alternative to Thompson’s Water Seal, there are many options available. Depending on your specific needs and preferences, any of the above-mentioned products will offer a high level of waterproofing protection.
How long does it take for Olympic Waterguard to dry?
Olympic Waterguard requires ample time to properly dry. Depending on the climate and humidity of the local area, the drying time can vary. On average, it takes between 8 and 24 hours for Olympic Waterguard to completely dry.
To ensure the best results, it is recommended to wait 24 hours before re-coating or allowing traffic onto the application area. Be sure to read and follow the instructions in the product label for the best results.
Is Olympic the same as Thompsons?
No, Olympic and Thompsons are not the same. Olympic is the brand name of the company Olympic Weight Plates and Thompsons is the brand name of the company Thompsons Fitness. Olympic Weight Plates is well known for their Olympic-style weight plates while Thompsons Fitness is renowned for their HIIT-focused gym equipment.
Olympic Weight Plates provide quality weight plates that are typically sold in sets and are ideal for traditional strength training workouts. On the other hand, Thompsons Fitness provide a range of versatile equipment that can be used for high intensity interval training (HIIT) workouts.
Additionally, Olympic Weight Plates use colorful design and labeling to differentiate the weight plates and Thompsons Fitness uses a heavy-duty steel construction for a sturdy build. Finally, Olympic Weight Plates offer a range of affordable weights while Thompsons Fitness provides higher quality, but more expensive options.
What is the difference between water sealer and Waterproofer?
Water sealer and waterproofer are two products designed to protect surfaces from water damage. While they both share a common purpose, their methods of application and effects are quite different.
Water sealer is a liquid- or water-based product applied to porous surfaces, such as brick and concrete. Its purpose is to create a barrier on the surface to keep moisture out. Water sealer will not make the surface waterproof, however, it will make the surface resistant to water absorption and water damage.
Waterproofer, on the other hand, is a mixture of oil and waxes applied to surfaces like wood and stone. This product forms an impermeable barrier that blocks water from passing through the material and penetrating the core.
Waterproofer makes the material more waterproof than water sealer, and can even be used to slow down water seepage through porous materials.
Overall, water sealer is used to protect surfaces from water damage by creating a water-repellent barrier that prevents water absorption. On the other hand, waterproofer is applied to surfaces to create an impenetrable barrier that blocks water from entering the materials altogether.
Does Thompson’s water Seal work on stone?
Yes, Thompson’s Water Seal can be used effectively on stone surfaces. It is a water-based sealer that is specifically designed to protect wood, brick, concrete, and stone surfaces from water damage. The water seal penetrates the surface of the stone to form a protective barrier that resists water, oil and dirt.
It works to keep stone surfaces looking like new and prevents stains and wear. Additionally, Thompson’s Water Seal is easy to apply and can either be sprayed on or brushed onto the surface. After the sealer has been applied, it will take approximately 4-6 hours to dry before it is waterproof.
It is also important to note that Thompson’s Water Seal is not recommended for tile, grout, marble or granite as it may damage these surfaces.
Where can I use cementitious waterproofing?
Cementitious waterproofing is a type of waterproofing system that is often used to protect buildings and structures from water damage. It is typically used on structures like retaining walls, bridges, tunnels, and buildings.
It can also be used in other applications such as waterproofing basements and foundations, protecting decks, and increasing the structural integrity of concrete. Cementitious waterproofing is a popular choice because it is relatively easy to apply, relatively cost-effective, and provides a long-term waterproofing solution.
Additionally, cementitious waterproofing systems create an impermeable barrier against moisture, without causing any adverse effect on the environment. Furthermore, it can be customized to fit the needs of each particular project, allowing for versatile application.
How long does Thompson’s wood Sealer last?
Thompson’s® Wood Sealer provides long-term protection against the elements and keeps wood looking great for years to come. The product is designed to protect against sun, rain, and other outdoor elements, while also preventing the growth of mildew and mold.
The longevity of Thompson’s® Wood Sealer varies depending on the amount of direct sun exposure, humidity, and other environmental factors, but it typically lasts up to three to five years. It is important to re-apply the sealer periodically to ensure that wood is properly protected and looking its best.
How often do you have to apply Thompson water Seal?
Thompson Water Seal should be applied to the outside of the wood every two to three years, depending on the environment and how much wear and tear the wood receives. The best way to tell if a sealant needs to be applied is to inspect the wood at least yearly.
If the wood starts to show signs of wear, such as fading, discoloration, erosion or cracking, then it is time to reapply the sealant. It is important to use a good quality product like Thompson Water Seal to ensure maximum protection against the elements.
It is also important to follow the directions on the package, which may vary depending on the outdoor environment. Some sealants may need to be applied more frequently in areas with high humidity or heavy rainfall.
How good is Thompson’s water Seal?
Thompson’s Water Seal is a very good product when it comes to waterproofing and protecting outdoor surfaces. It can help to protect decks, fences, brick, concrete, and other outdoor surfaces from the elements, helping to keep them looking great for longer.
It provides a waterproof barrier against water and its advanced technology helps to repel moisture and prevent future damage. It is also easy to apply and clean up, making it a great choice for any DIY homeowner.
It also serves to protect surfaces from UV damage, helping to maintain the color of the surface and reducing the likelihood of fading or cracking over time. In summary, Thompson’s Water Seal is a great product for any outdoor surfaces, helping to protect them from moisture, water, and UV damage.
How many coats are there in Olympic water Seal?
Olympic Water Seal has a variety of products each with a variety of coating options, so it is difficult to provide an exact number of coats. However, most Olympic Water Seal products contain two coats.
This includes the Olympic Water Seal Maximum Clear Exterior Waterproofing Sealant which provides two coats of waterproof protection. The first coat seals and waterproofs the surface, and the second coat strengthens the seal and seals out moisture.
Other products, like Olympic Water Seal Multi-Surface Waterproofer, provide a one-coat application for maximum protection.
Can Olympic WaterGuard be applied to damp wood?
Yes, Olympic WaterGuard can be applied to damp wood, but there are precautions that should be taken. It is important to make sure the wood is completely dry before applying the product, otherwise it may not bond properly.
Additionally, it is recommended to wait 48 hours after the wood has been wet before applying the product. This will give the wood time to thoroughly dry out and allow the WaterGuard to properly adhere.
It is also important to clean the wood with a mild detergent such as TSP before applying the product. This helps to remove any dirt or grime so the WaterGuard can make a stronger bond. It may also be a good idea to give the wood sufficient time to dry out in the sun after cleaning.
Following these steps will help ensure the success of the WaterGuard sealing the wood.
Is Olympic wood stain any good?
Olympic wood stain is a popular and well-regarded brand of wood stain. It is known for its superior performance, durability, and easy application. It offers a wide range of colors and finishes to suit all tastes, and some of its products are even moisture resistant.
Olympic wood stain is also low in volatile organic compounds (VOCs) and doesn’t contain any harmful chemicals, making it safe for indoors use. Furthermore, Olympic stain offers an environmentally friendly water-based formula, which means it won’t create hazardous waste.
In terms of performance, Olympic wood stain provides excellent coverage, with a smooth and consistent finish. It is user-friendly and relatively easy to apply, although it does take a bit of practice.
All in all, Olympic wood stain is a great choice for any woodworking project.
What is semi transparent deck stain?
Semi-transparent deck stain is a type of deck finish that gives wood a tint or hint of color, while still allowing the wood grain to show. This type of stain is a great option for decks that are already in good condition and only need a touch of color.
It’s a great way to make an old deck look like new. The semi-transparent finish helps to protect the wood from UV rays, mildew, and water damage, while still allowing the natural beauty of the wood to show.
Semi-transparent deck stain is available in a variety of colors, so it can easily be matched to your existing décor or to create a specific look. It’s easy to apply and re-apply, so you can change the look of your deck with just one coat.