When it comes to sharpening a chainsaw, the degree of the angle of the cutters on the chain needs to be maintained in order to increase its lifespan and efficiency. When sharpening a chainsaw chain, generally you will want to sharpen it to an angle of 30°.
It is important to understand that if the angle is too small (e. g. 25° or lower), then the chain won’t stay sharp for very long and it could cause the chain to bind up. If the angle is too large (e. g.
35° or higher), it will cut slower and could cause the chain to stretch out faster and come apart. The correct angle for sharpening a chainsaw chain is crucial for a safe and efficient saw.
The angle of the cutters can be maintained using a file, guide, or professional sharpening jig. It is important to remember that sharpening the chainsaw too often can actually reduce its lifespan, so it is best to sharpen when it is just starting to dull.
It is also important to sharpen each cutter evenly and at the same angle to ensure a consistent cut and even wear on the cutters.
How do I know what angle my chainsaw blade is?
To know what angle your chainsaw blade is, you will need to check the angle of the blade teeth. Depending on the blade, the angle can vary significantly, but generally speaking the angle of the teeth should be between 30 and 35 degrees.
This angle will also vary depending on the type of blade you are using and the type of material you are cutting. The easiest way to determine the angle of the blade is to use a protractor or angle finder, but you can also measure it by eye if you know what to look for.
To measure the angle by eye, line the saw blade up next to a straight edge and look for the angle at which the teeth on the blade converge. This angle is what you will use for the angle of the blade.
Once you know the angle of your saw blade, you can buy a blade specifically designed for that angle, or you can adjust the angle of the blade to get the desired results. It’s important to note that the angle of the blade will affect how the saw cuts, so be sure to check your blades and make any necessary adjustments.
What size file do you use on a 3/8 chain?
The appropriate size file to use on a 3/8 chain will depend on the chain size and number of drive links. Generally, chains come in 0.050″ (1.315mm) or 0.058″ (1.473mm) sizes, and most 3/8 chains will have either 62 or 72 drive links.
If the chain has 62 drive links, then you need a 5/32″ round-file (. 157″ or 4.00mm) for the standard cut, or a file with a square cross section for a deep cut. For a 3/8 chain with 72 drive links, you will need a 3/16″ round-file (.188″ or 4.
76mm) for the standard cut, or a file with a square cross section for a deeper cut. It is also important to make sure you buy a good quality file as should projections can get stuck in the drive links and damage the chainsaw.
What makes a chainsaw cut on an angle?
A chainsaw is able to cut on an angle due to the design of its chain. The chain of a chainsaw is razor sharp and made up of several small links connected together. The teeth on the links are angled so that when combined with the spinning motion of the chainsaw, it produces a cutting action similar to the action of a saw blade.
The angle of the tooth design combined with the speed of the spinning chain can create intricate cuts on both hard and soft woods. In addition, the chainsaw has a bar with an adjustable angle, allowing users to rotate the chainsaw in order to make angled cuts in wood.
What angle is a chainsaw tooth?
The angle of the chainsaw tooth is determined by the diameter of the saw blade. Generally, the angle of a chainsaw tooth ranges from 0 to 45 degrees. The larger the diameter, the sharper the saw blade and the steeper the angle of the chainsaw tooth.
The angle of the tooth typically varies between 0 and 15 degrees for small saw blades, and between 15 and 30 degrees for mid-sized saw blades, and 30 to 45 degrees for large saw blades. It is important to use the correct angle for your saw blade size in order to maximize efficiency and ensure a clean, accurate cut.
Each designed for specific use, such as cross-cutting, ripping, and deep cutting.
What’s better full chisel or semi chisel chain?
The answer to this question depends on your needs and preferences as a user.
Full chisel chains are often preferred by professional loggers or experienced woodcutters. This type of chain is designed for maximum cutting power and durability. The teeth are designed to stay sharper for longer, which results in faster cutting.
Additionally, full chisel chains tend to require less maintenance than semi chisel chains, as their larger, sturdier design helps to maintain the sharpness of the teeth for longer.
Semi chisel chains are usually preferred by novice woodcutters. This type of chain is designed for operator safety, as the rounded and semi-symmetrical teeth tend to reduce kickback while cutting. This type of chain also requires less power to cut, which makes them easier to handle.
However, semi chisel chains may require sharpening more frequently, as the smaller less sturdy design tends to dull faster.
Ultimately, your decision should be based on your experience level and the type of cutting you are doing. If you are an experienced user looking for maximum cutting power and less maintenance requirements, then a full chisel chain is likely your best option.
However, if you are a novice user who values safety and ease of use over cutting speed and power, then a semi chisel chain may be a better choice.
What degree is a ripping chain?
A ripping chain is a type of chain specially designed for the purpose of ripping along the grain of a piece of lumber. This type of chain is typically used on the cutting surfaces of table-saw and radial-arm saws.
Ripping chains consist of sharp, wide cutters which cut in a ripping action, rather than the cutting action of the standard-tooth chain. The degree of the ripping chain is determined by the angle of the cutters, which is usually between 5 and 20 degrees.
Furthermore, the cutters on the ripping chain may feature either chamfered or radiused corners.
What type of chainsaw chain cuts the fastest?
The type of chainsaw chain that cuts the fastest is typically a full-complement chainsaw chain, sometimes referred to as full-chisel chainsaw chain. This type of chain features a full set of cutting teeth and is designed for maximum cutting speed.
In comparison, semi-chisel chainsaw chain has fewer cutting teeth, resulting in less cutting speed, but more efficiency and less vibration. There are also specialty chainsaw chains, such as low-vibration chains and skip-tooth chains, that offer the user a variety of options depending on the cutting job.
Ultimately, the type of chain that will cut the fastest depends on the cutting job and the user’s preference.
What pitch is my STIHL chainsaw chain?
The pitch of your STIHL chainsaw chain will depend upon the model of the saw and the type of chain. STIHL offers a wide variety of chainsaw chains, with different pitches available from 1/4” to 3/4”.
To determine the pitch of your STIHL chainsaw chain, you will need to consult your STIHL chainsaw owner’s manual. The manual will list the dimensions of the chain as well as its pitch. It should be noted that some models might also offer a low kickback chain option, which has a slightly different pitch than the standard chain that comes with the saw.
It’s important to use the correct chainsaw chain for your model and to ensure that you are matching the right chainsaw chain to the bar length on your saw. The wrong chain size can be dangerous and can even cause damage to the saw.
What kind of chain does STIHL use?
STIHL uses a semi-chrome plated corrosion-resistant steel chain with 3/8 inch pitch and low kickback capability. The chain is made of a material that has been through a special hardening process to make it tougher and more durable than other steel chains.
The chain also features a cutting edge design which features narrow grooves that provide longer cutting life and smoother cutting. The chain also has been designed to resist the damages caused by harsh working conditions and extended cutting time.
What is the difference between .325 and 3/8 chain?
The. 325 chain is a saw chain used in chainsaws. It is a standard cutting chain that is used on saws from leading manufacturers such as Stihl and Husqvarna. The. 325 chain uses slim blades that are. 043 inch wide in cutter thickness and 3/8 inch in pitch.
It is a low-kickback, standard-duty chain that is designed for general-purpose cutting.
The 3/8 chain, on the other hand, is a saw chain that is a larger, beefier option with thicker cutters. It uses cutter blades that are roughly. 050 in thickness and 3/8 inch in pitch. It is made for semi-chisel cutters and is the standard-duty chain of choice for professional loggers because of its higher durability and cutting performance.
It is capable of handling bigger, tougher jobs found in the logging industry.
What do the numbers mean on Stihl chains?
The numbers on Stihl chains refer to different characteristics to help you select the right chain for your needs. The numbers indicate the pitch, which is the distance between the drive links (connector links) of the chain, the gauge of the drive links, the number of drive links and the chain type.
The first number indicates the pitch of the chain. The most common pitches are 0.325”, 3/8”, or 0.404”.
The second number indicates the gauge of the drive links. The most common gauges are .043”, .050” and .058”.
The third number indicates the number of drive links in the chain. For example, a sixty-five drive link chain has “65” printed on it.
The fourth number indicates the chain type. The types available are the Micro Lite, Rapid Micro, or the normal chains.
By knowing the numbers on a Stihl chain, you can make sure to get the right chain for the task you need to complete. Choosing the right chain will enable it to last longer and perform better.
Will an Oregon chain fit a STIHL?
No, an Oregon chain will not fit a STIHL saw. A STIHL saw will require its own brand or compatible chains such as Carlton, Oregon, Oregon Pro-Lite, or Oregon VersaCut to fit. If a saw is labeled with an Oregon logo, it likely means that it was built on a STIHL platform, but the chain may not be an Oregon brand.
Oregon chains tend to fit a wide variety of saws, and Oregon chains are available in multiple pitches, gauge sizes, and are available with skip, semi-skip, or full chisel or micro chisel configurations.
It is important to consult the manufacturer’s website to get the right type and size of chain for your saw.
Can you use any brand chain on a STIHL chainsaw?
Yes, you can use any brand chain on a STIHL chainsaw. All STIHL chain saws are equipped with an OILOMATIC® saw chain, designed to provide superior cutting performance and extended life for all STIHL chainsaws.
This chain is designed to work well with a specific pitch size, gauge, and sequence of cutter links. Many chains that are sold on the market today come equipped with the same pitch and gauge size but may have a different sequence ofcutter links.
This may decrease the life of the chain, but it can still be used on a STIHL chainsaw. Be sure to follow the owner’s manual instructions when installing and using any chain on your STIHL chainsaw.
Who makes STIHL chains?
STIHL chainsaws and accessories are made by the STIHL company, a Germany-based manufacturer that has been in business for over 100 years. When Andreas Stihl, the founder of the company, created the first chainsaw in the 1920s, he set a new bar for chainsaw quality, performance, and durability.
Since then, STIHL products have been synonymous with quality and innovation, with their chainsaws and accessories being used by professionals, hobbyists, and everyday users alike. Each STIHL chainsaw is made with precision and care, using the latest technology and designs in order to guarantee top performance.
They are made by highly skilled workers in a state-of-the-art production facility and are quality tested before they ever reach the shelves. STIHL chainsaws are made to last and can handle any job you throw at them, giving you long lasting performance you can count on.
