AdvanTech flooring is a high-performance engineered wood product designed for installation over wood or concrete substrates. It is made with a core of veneer strands that are pressed together for strength, then fused together with a resinous thermosetting adhesive.
The strands are oriented at right angles to each other, which adds strength and rigidity. Not only is this product strong and dimensionally stable, but it is also lightweight and easier to handle and install than solid wood flooring.
It also resists moisture, scratches and dents better than solid wood, making AdvanTech a great choice for areas exposed to high traffic and moisture. AdvanTech’s high density also reduces noise transfer when walking on the floor, which is great for multi-level homes.
All AdvanTech flooring products are third-party verified for strength and moisture performance and come with a lifetime limited warranty for peace of mind.
- Is AdvanTech OSB or plywood?
- Is AdvanTech better than OSB?
- What is the sub flooring to use?
- What is the plywood to use for subfloor?
- What thickness subfloor is recommended?
- Can OSB be waterproofed?
- How thick should plywood subfloor be?
- Is it better to use OSB or plywood for subfloor?
- How much does a sheet of 3/4 AdvanTech plywood weigh?
- What thicknesses does AdvanTech come in?
- What goes on top of AdvanTech subfloor?
- Do you nail or screw subfloor?
Is AdvanTech OSB or plywood?
AdvanTech is neither OSB nor Plywood. It is a high-performance engineered wood panel product manufactured by Huber Engineered Woods. It is made with an advanced resin technology and has a proprietary wood strand combination, as well as multiple layers of protection against weather, moisture and other environmental conditions.
It has better strength and stiffness than traditional OSB and Plywood, as well as improved fastener holding power, which makes it a great choice for overly wet, unstable, or high-exposure framing projects.
AdvanTech can also be used as sheathing, subflooring, wall sheathing, and more.
Is AdvanTech better than OSB?
When comparing AdvanTech and OSB, there are a few factors to consider. Both materials are designed to function well when used in exterior sheathing applications. However, AdvanTech is a bit heavier and more expensive than OSB, which is lighter and less expensive.
AdvanTech has integrated water-resistive barrier protection and high nail-holding strength. It also has a higher design-value capacity and improved sag-resistance, making it particularly well-suited for areas where additional support is necessary.
And, it has been treated with a zinc borate to help protect against mold and fungal growth. OSB, on the other hand, is rated for sheathing applications and provides great moisture resistance, but does not include a mold or fungal treatment.
When taking into account both cost and performance, it can be difficult to determine whether AdvanTech or OSB is better. If cost is the main concern and the project does not require long-span installations or increased performance, then OSB may be the better choice.
But if the project needs extra strength and needs to be protected from fungal damage, then AdvanTech might be the better option. Ultimately, the decision should come down to the needs of the project and the unique circumstances of the job site.
What is the sub flooring to use?
The type of subfloor you should use depends on the specific application you plan to use it for. Generally, the best subflooring to use is OSB (Oriented Strand Board) or plywood. OSB has a smooth, even surface and flatness and is ideal for regions with high moisture.
Plywood is slightly more expensive than OSB, but is more resistant to moisture and offers superior strength and stability. It is also easier to work with than OSB, due to its tongue and groove panels.
When installing subflooring, it’s important to select the most suitable type for your application and to use the proper materials and hardware for the project. Additionally, you should use screws or nails that are the correct length for the subflooring material and substrate, and install them in a grid pattern.
Proper installation of subflooring will ensure a secure and durable finished product.
What is the plywood to use for subfloor?
The type of plywood to use for a subfloor depends on what type of flooring material you plan to install on top of the subfloor. For most tile, vinyl and hardwood flooring, use a 5/8” or thicker, exterior-grade plywood with a “C-D” grade or better.
Other suitable options include OSB (oriented strand board) or an engineered wood structural panel. A subfloor should also be sealed with a vapor retarder, which helps keep moisture from seeping into the subfloor material, causing it to rot.
Make sure the subfloor is level and any nails or screws are flush and securely fastened. To create a subfloor for hardwood flooring, use thicker plywood, such as ¾-inch CDX plywood, which is slightly more expensive than 1/2-inch CDX plywood.
When installing hardwood floors, use a construction adhesive to adhere the plywood to a concrete floor. Additionally, make sure to reinforce the subfloor’s joints and edges with treated lumber.
What thickness subfloor is recommended?
The recommended thickness for a subfloor typically depends on the specific application and the types of materials being used, but in general, thicker subfloors will provide a stronger and more stable flooring surface.
For instance, if you are installing a hardwood floor, even on a ground-level, it is recommended to use a 5/8″ subfloor, as this will provide the most stable foundation and help prevent squeaks and shifting over time.
Plywood and other composite subfloor materials can come in even thicker varieties, such as 3/4″ and 1″, which could be recommended depending on the installation. For example, when installing tile, a 3/4″ subfloor is usually needed for added support to prevent cracking.
If a subfloor is being installed in a basement, the thickness can vary but it is recommended to use a thicker subfloor such as 1/2″ or 3/4″ as basements are typically subject to more fluctuating temperatures, moisture, and other conditions which can cause movement in the subfloor.
Can OSB be waterproofed?
Yes, OSB (oriented strand board) can be waterproofed. OSB is a type of engineered wood made from strips of wood that are bound together with adhesive and compressed into a sheet material. OSB is often used in construction projects as an alternative to plywood because it is strong, lightweight, and can be more cost effective.
However, as with any wood product, OSB is not inherently waterproof. Waterproofing OSB is possible with the right products and techniques. The best way to waterproof OSB is to apply a penetrating sealer, such as a water-based acrylic.
This helps to seal up the wood and protect it from moisture, while allowing the wood to breathe. Another option is to apply a waterproofing membrane, such as a rubber membrane, which is applied with an adhesive to the OSB and provides a strong barrier against water.
You may also want to consider using paint or a liquid sealer to waterproof your OSB.
How thick should plywood subfloor be?
The thickness of plywood subflooring typically ranges from 5/8 to 3/4 inch, depending on its intended application and the building code in your region. For example, some building codes require at least 15/32 inch for bedrooms and 5/8 for other areas.
If you are unsure what the code requires for your application, you should consult a local building inspector for the correct requirements.
When installing the plywood, you should make sure to always use high-grade plywood, such as exterior-grade plywood or BCX, because they are much more durable and resistant to water and moisture. Additionally, you should use a good glue adhesive to ensure a secure bond between the plywood and the joists.
Generally, the thicker the plywood is, the sturdier the subfloor will be, so thicker plywood will provide more support for the floor system.
Is it better to use OSB or plywood for subfloor?
It depends on your project needs, budget, and desired finished look. Oriented strand board (OSB) is a cost-effective and reliable product for use in subfloors and sheathing applications. It is water resistant and can work as a flooring panel in many cases.
Plywood is more of an upgrade than OSB, as it is a bit more structurally sound and has a more finished look. It is however more expensive than OSB and is more affected by water and humidity, so it may not be suitable for all subfloor applications.
Generally, OSB is more widely used for subfloors and sheathing, while plywood may be more effective and aesthetically pleasing in certain circumstances. Ultimately the best option for your project will depend on the individual application and your desired finished look.
How much does a sheet of 3/4 AdvanTech plywood weigh?
The weight of a sheet of 3/4″ AdvanTech plywood will depend on the dimensions of the sheet. Generally, 3/4″ AdvanTech plywood will weigh approximately 50 pounds per 4×8 sheet. However, the exact weight can vary depending on the adhesive and core construction used.
Weight can range from 40-60 pounds per 4×8 sheet. The plywood can also come in other thicknesses, such as 1/2″ and 5/8″. If a sheet is not 4×8, the weight should be calculated by multiplying 50 pounds per 4×8 sheet by the total square feet of the sheet.
For example, if the sheet is 6’x3′, the approximate weight will be 30 pounds (50 lbs. per 4×8 sheet x 6 square feet of the sheet/32 square feet of a 4×8 sheet).
What thicknesses does AdvanTech come in?
AdvanTech® flooring is available in two different thicknesses – 23/32″ and 15/32″. The 23/32″ thickness is the most popular, and provides superior strength and stability to the flooring system. It has an overall premium performance rating of up to 120% better than commodity OSB.
The 15/32” version is designed to be the most cost-effective option and is perfect for non-structural sheathing applications. Both options come with an advanced moisture resistance and feature a pre-printed alignment guide, allowing for accurate and easy installation.
Both thicknesses have a tongue-and-groove design that enables a locked-together 30/15 SHE load span rating and a 300 day no-sanding warranty — making them perfect for a wide range of uses and jobs.
What goes on top of AdvanTech subfloor?
The type of flooring installed on top of AdvanTech subfloor ultimately depends on the room or space’s desired look and feel. AdvanTech subflooring is designed to provide superior strength and durability, making it an ideal base layer for nearly any type of flooring material.
Common flooring materials installed on top of AdvanTech subfloors include bamboo, carpet, cork, laminate, vinyl, hardwood, and ceramic tile. In some cases—such as concrete subfloors—the AdvanTech layer may be used as the finished surface.
It’s best to consult with a flooring expert for more specific recommendations about the best flooring for to install on top of AdvanTech subflooring.
Do you nail or screw subfloor?
For the most part, you will want to use nails when installing subfloor. Nails provide more stability and hold the pieces of the subfloor layer securely in place. You could use screws, which are easier to work with for some types of flooring and can be easier to remove if needed; however, nails offer better long-term stability and shouldn’t loosen over time.
Depending on the type of flooring that you’re installing, you might need to use both nails and screws as some types of flooring require a combination of the two.
When nailing subfloor, it’s important to use the right type and size of nail. For a plywood subfloor, you should use a 10-penny (or 10d) common nail that’s at least 2 1/2 inches long. For an OSB subfloor, use a galvanized roofing nail that’s between 1 3/4 and 2 1/2 inches long.
If you’re using screws, you should use a #10 or #12 self-tapping screw that’s at least 2 inches long.