The minimum thickness for a planer will depend on the size of the planer and the material being worked with. In general, planers can range from 3 inches to over 8 inches in size, so the required thickness can vary.
Generally speaking, the minimum thickness for a planer should be no less than 1/8 of an inch. This is to ensure that the material being worked with is not damaged by the cutting blades as they pass through it.
Different planers will have specific requirements, so it is important to read the manufacturer’s instructions before beginning any work. It is also important to note that when working with hard woods, the minimum thickness may need to be greater in order to prevent breakage or cracking.
What is the shortest board you are allowed to run through the thickness planer?
The shortest board you are allowed to run through a thickness planer is dependent on the size of your thickness planer, but most models should be able to handle a board that is at least 6 inches in length.
Generally speaking, the shorter the board you feed into the planer, the harder it will be to achieve an even cut due to the smaller surface area that the blades will be working with. Additionally, when using extremely short boards, there is an increased risk of kickback, so it’s very important to closely follow safety guidelines to ensure your own safety and the longevity of your equipment.
How do you use a Dewalt planer dw735x?
Using a Dewalt planer dw735x is a relatively simple process, as long as you have the right safety measures in place.
Start by making sure the planer is securely locked in place and the power cord is properly plugged in. Then, adjust the settings depending on the material being planed and the desired depth. Make sure to use the push blocks when feeding the material through the planer.
It’s important to keep the board straight during feed and ensure that the pressure is consistent. Check for any chips, streaks, or snipe on the leading and trailing edges with a ruler. Once finished, clear the planer and the area of any objects or shavings.
Be sure to wear protective glasses and outer clothing when using the planer and always disconnect the power cord after use. Also, keep the planer clean, check for any broken pieces, and read the user manual regularly for further instructions.
Last but not least, never plan any material other than wood.
What is the dial on the side of a Dewalt planer for?
The dial on the side of a Dewalt planer is used to adjust the cutter depth. This can be used to control the amount of material that will be removed from the wood piece when it passes through the planer.
The dial can be set to a specific depth or adjusted for very subtle changes in the depth of cut. This is important for achieving a more precise finish and for setting the planer to the wood’s stock thickness.
It is important to take time to understand the dial’s adjustment range before planing and to use a dial caliper to precisely measure the stock thickness. This will help ensure a successful planing process and result.
What can a thickness planer be used for?
A thickness planer is a woodworking tool used for achieving a precise thickness for a board. It works by taking a board and passing it through two adjustable rollers which are powered by an electric motor.
This allows you to plane the thickness of the board to any precise thickness. A thickness planer can be used for a variety of purposes including surfacing larger boards, flattening boards to a precise thickness, reducing the thickness of a board, and cleaning up warped edges.
This makes it an invaluable tool for many woodworking projects such as furniture making, cabinetry, shipbuilding, and more. With the help of a thickness planer, you can ensure that all your boards have consistent thicknesses, making them all ready for whatever project you have in mind.
What can you do with a wood planer?
A wood planer is a handy tool that can be used to smooth, shape and dimension lumber to precise specifications. With a wood planer, you can craft precise pieces with unique shapes and joints. You can use a wood planer to adjust the thickness of a board, to square the edge of a board, to rabbet a board to make a butt joint, even to chop the ends of boards to make a flat surface for a tabletop.
Furthermore, a planer can be used to level out blocks and boards, to reduce the dimensions of a board, grade out and square up lopsided boards, and much more. Overall, a wood planer can make all the difference when it comes to creating smooth, precise wood pieces with a professional finish.
Is a planer worth the investment?
The answer to this depends on individual circumstances and what kind of planer you intend to purchase. Generally, planers are an excellent investment for people who regularly work with wood, as they help create a smoother, more even surface.
With the use of a planer, it is possible to customize lumber dimensions to fit any project. You can also speed up the woodworking process with a planer, as they can turn rough lumber into finished pieces quickly.
When deciding if a planer is worth the investment, consider the cost and what type of planer you are looking at. Quality planers will cost more but will give you the best surfaces, performances and features.
Cheaper planers are limited by low power and cannot create the same surface quality as quality planers.
Also consider your woodworking projects and what type of performance you need. If you are looking to increase production speed, then a planer is an excellent investment. If you are only looking for simple projects, then you may not need a planer.
Overall, planers can be a great investment for those that work with wood and need to customize projects quickly and efficiently. They can save time and money, making them worth the investment if you are looking for high quality results.
What is the difference between DeWalt DW735 and DW735X?
The DeWalt DW735 and DW735X are both two-speed planers designed to precisely shape and contour wood and other materials. The DW735 has a 3-knife cutter head with disposable knives, while the DW735X has a 12-1/2 inch, three-knife cutter head with reversible knives that can be sharpened when needed.
The DW735X also includes an additional 13 inch infeed and outfeed tables, which provide better material support for longer boards and more accurate cuts. Additionally, the DW735X has increased power at 15,000 RPM to accommodate harder woods and thicker material.
Additionally, both models come with a dust hose that connects to a vacuum for dust-free work. The DW735X also includes larger adjustment knobs and a better depth adjustment system for precise thickness control.
Overall, the DW735X is better than the DW735 in terms of power, precision, dust management, and material support.
Are DeWalt planer blades reversible?
Yes, DeWalt planer blades are reversible. Depending on the type of planer model, the blades are typically mounted on the drive head and able to be flipped over when one side of the blade has become dull.
Be aware that flipping the blade over will reverse the direction of cutting, so it is best to be done when the planer isn’t being used. Additionally, the blades must be secured when removed from the planer for safety reasons.
The manufacturer directions should be followed for any planer changes to ensure the proper method of reversing the blades.
How do you rotate a dEWALT planer blade?
Rotating the blades on your DeWalt planer is a necessary step for ensuring that you get the best results when using the tool. The following are the steps for rotating a DeWalt planer blade:
1. Start by unplugging your planer from the power source and removing the blades from the planer.
2. Now place the flat side of the tool against a flat surface. This will help you to rotate the blades without making them blunt. With the planer in the horizontal position, use a wrench to loosen the blade cap screw located at the end of the blade.
3. Once the cap screw is fully loosened, you can easily rotate the blade while still holding it in the horizontal position. Make sure that the angle of the blade remains in the same position as you rotate it.
4. Once you have rotated the blade in full, tighten the cap screw to secure the blade in its position.
5. Finally, re-insert the blades into the planer and plug it into the power source.
You should ensure that you rotate the blades regularly to ensure that the blade is sharp enough to perform the desired task. If you notice the blades have become blunt, you should replace them with new ones to ensure the best performance from your DeWalt planer.
Which way do dEWALT planer blades go?
When installing DEWALT planer blades, they should be installed so the beveled edge is pointing downwards. This is because bevels on the blade provide a cutting edge and helps the planer blades cut through the material more easily.
Additionally, the bevels provide support on the exit side of the cut. If the blades are installed with the beveled edge facing upwards, the blades may not achieve an even cut and could result in a poor finish.
To properly install DEWALT planer blades, start by firmly gripping the blades and rotating them 180 degrees so the beveled edge is facing downwards. Make sure to securely fasten the blades in place to ensure safe and effective use of the planer.
How many HP is DW735?
The DeWalt DW735 portable planer has a motor that produces up to 20,000 RPM, or revolutions-per-minute, with a maximum power rating of 15 amps. This translates to about 1.5 horsepower (HP). That’s the maximum power rating for the DeWalt DW735, so it’s best to not exceed this rating.
The DeWalt DW735 is a heavy-duty planer that utilizes a heavy-duty motor that offers robust power for planing even tough woods. It has quickly become one of the most popular and versatile portable planer models on the market.
Does the Dewalt DW735 come with blades?
No, unfortunately the Dewalt DW735 does not come with blades. If you are in need of blades to use with the DW735, you can purchase them separately at any local home improvement store or tool center as well as many online retailers.
The blades that this model uses are usually 12-1/2 inches in length and come in either a tooth count of 24 or 80. Be sure to double check before purchasing a set, as size and tooth count can vary from brand to brand.
Is the Dewalt 735 worth it?
The Dewalt 735 is a popular option for those looking for a good quality planer that won’t break the bank. It is well built and designed to take on a variety of jobs. The 735 offers a feature set that puts it at the top of many carpenters’ lists.
The powerful 15 amp motor is capable of reaching an impressive 13,000 RPM, allowing for deep and precise cuts. The three knife setup is an impressive feature for a planer of this price. You can also easily change the depth of cut and the fence angle, without having to make adjustments to the knives.
The height adjustment is both easy and accurate, taking the guesswork out of setting the planer height. And the built-in dust collection system is another plus, which helps keep your work area clean.
Overall, the Dewalt 735 is definitely worth it. Its superior craftsmanship and strong motor mean you will get consistent, high quality results. The three knife setup, dust collection system, and ease of use make it an ideal choice for amateurs and pros alike.
If you are in the market for a good planer, the Dewalt 735 is definitely worth considering.
Is the DW735 better than the DW734?
The DW735 is definitely an upgrade from the DW734, offering more power, versatility, and convenience. The DW735 has a more powerful 15-amp motor that operates at up to 20,000 RPM, which is 3,000 RPM more than the DW734.
Additionally, this model has a greater cutting capacity and can tackle materials up to 13 inches wide, which is 3 inches wider than the DW734. The DW735 also has a larger cutter head that holds three cutting blades at once, allowing users to make cuts up to 99 layers thick in one pass.
Finally, the DW735 can easily be adjusted to handle different material thicknesses, while the DW734 requires an EZ-Set depth-stop system to make these adjustments. All these features combined make the DW735 the superior choice for anyone that needs to make accurate and precise cuts.
How many amps does Dewalt 735 planer use?
The exact amperage requirements of the DeWalt 735 planer depend on the type of power source you are using. If you are using a 120V outlet, the planer will use a maximum of 15 amps. However, if you are using a 240V outlet, the maximum amperage output of the planer is 12.4 amps.
Therefore, depending on your power source the DeWalt 735 planer can use either a maximum of 15 amps or 12.4 amps.
Is DeWalt planer good?
The DeWalt Powermatic planer is generally a good choice for both professional and home woodworkers. It is powered by a strong 13 amp motor and has a three blade cutter head which provides a perfect finish to any piece of wood.
The cutter head is adjustable, allowing for a variety of different cuts, and the planer is relatively quiet and safe to use. The DeWalt is also easy to assemble and use, and it is backed by the company’s reliable customer service and warranties.
Additionally, the DeWalt planer is durable enough to handle a lot of wear and tear and won’t be easily damaged by everyday use. All in all, it is a great choice for both professionals and hobbyists alike.
Does DeWalt have a jointer?
No, DeWalt does not currently offer a jointer. Jointers are specialized tools used to create flat surfaces along the edges of pieces of wood so that two pieces can be joined together with a tight fit.
DeWalt does offer a variety of other tools for woodworking, including saws, drills, sanders, and routers. Many of their tools feature cordless designs and innovative technologies such as FLEXVOLT, which allows you to switch between cordless and corded operation depending on the task at hand.
DeWalt also has a line of cordless outdoor equipment, such as string trimmers, chainsaws, and blowers, as well as a complete line of accessories including bits, blades, and more.