The Hercules miter saw carries a limited one-year warranty. This warranty is provided by Hercules and will cover all defects in material and workmanship in the saw itself. Hercules warrants the saw to be free from defects in material and workmanship, under normal use and service, for one year from the date of purchase.
In the event of a defect, Hercules will repair or replace products that prove to be defective and are returned to an authorized service center. Additionally, Hercules also offers a 30-day money-back guarantee in which consumers can return the saw within 30 days of purchase for a full refund if it does not meet your expectations.
All claims for any product defect must be made to Hercules in writing within the warranty period stated above.
How much is a Hercules miter saw?
The cost of a Hercules miter saw will depend on which model you’re looking at and where you purchase it from. Prices can range from around $160 for a 12″ compound miter saw to around $380 for a 12″ dual-bevel sliding compound miter saw.
Hercules Miter Saws are available for purchase at several retailers such as Amazon, Home Depot, and Lowe’s. Prices may vary slightly from store to store and can even depend on any specials or sales the store may have going on.
How do I change the blade on my Hercules miter saw?
Changing the blade on your Hercules miter saw requires several steps and should only be done by an experienced user. To get started you’ll need to make sure that your saw is unplugged and completely disconnected from any power source.
Then, proceed with the following steps:
1. Remove the saw blade guard, if applicable, by loosening and removing the screws.
2. Raise the arm of the saw to its highest position, then loosen and remove the blade lock knob.
3. Move the arm so that the blade is in a horizontal position and loosen the arbor nut to release the blade.
4. Carefully remove the blade and use an arbor washer to secure the new blade to the arbor.
5. Secure the arbor nut and make sure to properly tighten it so that the blade is secured in place.
6. Position the arm so that the blade remains in the horizontal position and reinstall the blade lock knob by securing any necessary screws.
7. Lastly, use the saw guard to cover the blade and make sure that it is securely attached.
Once you’ve finished these steps, your Hercules miter saw is ready for use with the newly installed blade. As always, be sure to take the necessary safety precautions when using any type of power tool, especially mitre saws.
Are miter saw blades reverse threaded?
No, miter saw blades are not reverse threaded. The blade of a miter saw is held in place with either a spindle lock or a table lock. The spindle lock is a collar that clamps the blade to the arbor, which is the shaft that rotates the blade.
To attach the blade, the collar is tightened using the arbor nut, which is tightened in the clockwise direction. Similarly, the table lock is tightened in the clockwise direction to secure the blade to the table.
Therefore, because the blade is secured in the clockwise direction, it is not reverse threaded.
How do you change a blade on a circular saw without a lock?
Changing the blade on a circular saw without a lock requires a few simple steps. Before getting started, make sure the saw is unplugged, and it’s a good idea to wear safety glasses and gloves.
Start by removing the blade guard and exposing the blade. If the saw has a threaded arbor nut (usually a 5/8” nut), you can use an open-end wrench to loosen it, then use your hands to unscrew it completely.
For saws without a threaded arbor nut, you will need to use a special arbor nut wrench to loosen it.
Once the arbor nut is off, slide the outer flange off and place it aside. Carefully remove the old blade from the saw by carefully pulling it out. Place the new blade on the arbor (a metal shaft that runs through the motor) of the saw and make sure it is properly oriented before tightening the arbor nut.
Once the new blade is in place, replace the outer flange with the black face of the flange facing away from the blade. Before turning the power back on and replacing the blade guard, make sure the blade is secure by wiggling the blade to make sure it is secure.
Once everything is secure, reattach the blade guard, plug in the saw, and you’re ready to get back to work!.
How do you remove a stuck chop saw blade?
Removing a stuck chop saw blade can be a tricky but important task. First, you should unplug the saw and make sure the blade has stopped rotating. It is important to wear gloves or protective gear to guard against injury.
Next, use an Allen wrench to loosen the blade bolts and pins. If the bolts will not budge, you can use a hammer to gently tap the wrench until the bolts loosen. Lastly, use a brush or wire brush to clear away dirt, grime, and other materials that may have lodged in the blade teeth.
Once the blade is completely dislodged and cleared of debris, you can remove it from the saw. Be sure to check the blade for wear, as well as the saw’s blade guard and flanges before reinstalling the new saw blade.
How do you change a miter saw guard?
Changing a miter saw guard can be a complicated process, depending on the type of saw you have and the condition of the saw guard. Generally, you can follow these steps to change the miter saw guard on most saws:
1. Unplug the miter saw from the wall and make sure it is turned off before attempting to change any parts of the saw.
2. Remove the blade of the miter saw. Most saws have a knob on the side of the housing that needs to be turned counterclockwise to remove it.
3. Once the blade has been removed, use a wrench to unscrew the bolts that hold the miter saw guard in place.
4. When the bolts are out, carefully remove the guard and inspect it for any damage.
5. If the guard is damaged, you’ll need to purchase a new one from your local hardware store or online.
6. Install the new guard in place of the old one by securing it with the previously removed bolts.
7. Once the new guard is in place, re-install the blade and plug the miter saw back into the wall.
8. Finally, you’ll want to test the saw to make sure the guard is properly secured in place and that the saw is working correctly.
What does a blade guard on a miter saw do?
A blade guard on a miter saw is designed to protect a user’s hands from the sharp saw blade. The guard is typically constructed from plastic or metal and attaches to the back of the saw’s table. It is designed to swing into place when the saw is switched on so that it covers the saw blade.
The guard ensures that your hands stay well away from the blade when the saw is in operation. It can also help to alleviate some of the sawdust produced during cutting. The blade guard should always be in place and easily seen before beginning a miter saw project.
How do you install blade guards?
Installing a blade guard is a straightforward process that requires few tools. First, you will need to disconnect the power from your saw. Next, use a wrench or screwdriver to loosen and remove the existing guard from the saw.
Once the existing guard has been removed, place the new blade guard over the saw blade, making sure it is aligned properly with the teeth of the blade. Secure the blade guard to the saw with the screws that are included or use screws of the same size.
Make sure the screws are tight, but don’t overtighten them. Finally, ensure that the blade guard is securely attached. You may need to adjust it to get the desired fit. After installation, reconnect the saw power and test the new guard to make sure it mows efficiently and safely.
How do you install a Dewalt miter saw deflector?
Installing a Dewalt miter saw deflector is a relatively easy job. The deflector can be found in any home improvement or hardware store.
The first step is to carefully read and follow all of the safety instructions that are included with the saw deflector. Be sure to wear safety glasses while working on the saw.
Next, detach the saw handle from the saw body. Using a flat-head screwdriver, unscrew the screws located on each side of the handle. Lift the handle away from the saw body.
On the underside of the handle, four screws are located. Unscrew these screws and lift away the saw shields.
Fold down the upper guard of the saw and use a hex key to loosen the bolt located on the inside edge of the guard.
Once the bolt is removed, you can raise the guard and place the deflector over the saw blade. With the deflector in place, secure it by reinserting the hex key and tightening the bolt.
Next, reattach the handle and saw shields. Secure the handle with the screws and make sure all of the screws are tightened properly.
Finally, flip up the guard to make sure the deflector is properly in place and working. Use the deflector when operating the saw to ensure safety and accurate cuts.
Who makes the Hercules compound miter saw?
Hercules is a line of affordable, high-quality power tools created by Infinity Cutting Tools. The company specializes in a wide range of woodworking tools and accessories, including the Hercules compound miter saw.
The Hercules line is designed to meet the needs of hobbyists, professionals, and industrial workers alike. The Hercules compound miter saws use a special combination of heavy-duty construction and precision parts to provide an accurate and efficient cut.
The saws also feature a special locking design that prevents debris from entering the blades, increasing safety and helping to promote a better cut rate. The Hercules compound miter saws are offered in a range of sizes and designs, so users can find a saw to meet their unique needs.
Most of the Hercules commands miter saws also come with a three-year warranty, showing the company’s commitment to producing quality tools.
How wide can a 10-inch miter saw cut?
A 10-inch meter saw can cut pieces that are up to 6-1/2 inches wide. This is due to the width of the blade, which is typically 5-1/2 inches. The additional inch comes from the 10-inches of the cutting area which includes the distance of the blade that projects out of the body of the saw.
The maximum depth of cut will depend on the type and size of the blade installed in the miter saw, although typically most 10 inch saws can make cuts up to 4 inches deep.
How wide is a Mitre saw blade?
The width of a mitre saw blade can vary depending on the model. Most mitre saw blades have widths that range between 5 and 12 inches, however, some have blades as small as 4 inches or as large as 14 inches.
The size of the blade typically depends on the size of the saw and what type of cuts it is designed for, as larger blades can make deeper cuts with more precision. You should refer to the manual for your specific saw for the exact size and type of the blade that should be used.
Can a 12 miter saw cut a 4×4?
Yes, a 12 miter saw can cut a 4×4. Miter saws have a variety of blade sizes, and the size of the blade will determine the size of the cut that the saw is capable of making. Most miter saws come with a 7 1/4 inch blade, which would allow the saw to cut a 4×4 in one pass.
If your miter saw does not have a 4×4 capacity, you can often get a larger blade for it in order for it to be able to make the cut. With the right blade, a 12 miter saw can definitely cut a 4×4.
Can you cut a wide board on a miter saw?
Yes, you can cut a wide board on a miter saw. This can be done by using a miter saw extension, also known as a cross cut sled. A miter saw extension is simply a wider table that attaches to your miter saw and provides more stability when making wide cuts.
It also helps support the weight of the material and keeps it from being too heavy for the saw. This type of extension is most often used when cutting wide boards, such as plywood, that requires accuracy and stability.
Additionally, when cutting wide boards, it is important to use a miter saw with a carbide-tipped blade, as this will give you a smoother, more accurate cut. Once the board is laid flat on the extension, make sure to use a saw that is set up to run in both directions so that you can make a cross cut while avoiding kickback.
Finally, be sure to wear safety glasses to protect your eyes from any wood chips created from the saw.
Can you use a miter saw to cut MDF?
Yes, you can use a miter saw to cut MDF. MDF stands for medium-density fiberboard and is a type of wood particleboard made from fine wood chips and particles, which are bonded together using adhesives and pressurization.
A miter saw is the ideal tool to make accurate cross, angle, and miter cuts in wood and other materials such as MDF. It is a compact, easy to use and safe power tool that attaches to a workbench. When cutting MDF with a miter saw, it is important to remember to use a blade specially designed for cutting this material, as regular blades for wood can leave a rough cut.
You should also wear safety goggles and a dust mask, as MDF gives off fine dust particles when it is cut. Additionally, it is preferable to use clamps to keep the MDF in position. Following these steps will help ensure that you make accurate and clean cuts in MDF with your miter saw.
What does cross cut capacity mean?
Cross cut capacity is a term used to describe the ability of a particular machinery or device to cut materials into a specific size or shape. Cross cutters are primarily used in woodworking, metalworking, and other applications where accurate cuts are required.
The capacity of a particular crosscutter varies depending on the size of the material it is designed to cut, the speed and power of the motor, as well as the type of blade used. A higher capacity cutter will be able to handle larger pieces of material, while a lower capacity cutter may struggle with thin or thin-walled materials.
Generally, the more powerful and fast the motor, the more capacity the crosscutter will have. Additionally, the type of blade used can impact the capacity of a crosscutter with certain blades being more effective at certain materials.
Are Mitre saw stands universal?
No, mitre saw stands are not universal. Different mitre saw stands can typically be used with a variety of mitre saws, but the size and weight of the saw can limit what mitre saw stands will work for it.
Additionally, the larger, heavier saws will require a heavier duty stand than the smaller, lighter saws. Also, if a mitre saw has a larger base and/or longer handles, it is likely that the stand must be able to accommodate these features.
Finally, some stands are designed to be used with specific models of mitre saws, so they may not be compatible with other models, even if they appear to be of similar size.
Where is the lock on my miter saw?
The lock for your miter saw is typically located at the back of the saw near where the blade is located. You may have to turn the saw upside down to locate it. In most cases, the lock is situated just in front of the blade guard and just behind the saw’s motor housing.
It looks like a small lever or knob that has to be pushed or turned to lock the blade in place. Depending on the model of miter saw, you may have to refer to the instruction manual in order to properly locate and identify the lock.
