The fence on a radial arm saw should be positioned upright with the cutting edge away from the operator. When in the correct position, the fence should be aligned with the cutting edge of the blade and the arm of the saw.
When making a cut, the fence should be adjusted so that it is aligned parallel to the cutting edge of the blade. The fence should be moved as far as possible away from the blade so as to provide the maximum distance between them, while still enabling the operator to make an accurate cut.
To ensure safety, the fence should be tight against the rip fence at the back of the saw. The fence should be adjusted to the desired distance from the blade before making any cut. It is important to be aware that the location of the fence should also be adjusted to account for the size and type of material being cut, as well as the specific saw model in use.
It is also important to make sure that the fence is locked into place before starting a cut.
Which way does the blade go on a radial arm saw?
The blade on a radial arm saw needs to be installed so that it rotates counterclockwise when viewed from the back of the saw, which is the direction for normal forward cutting. To install the blade, the lower guard needs to be opened and the proper sized arbor nut with washers needs to be placed onto the blade arbor.
Place the blade onto the arbor and secure with the arbor nut. Make sure the blade teeth and arbor nut are facing the same direction–counterclockwise when viewed from the back of the saw. Fasten the arbor nut with a wrench, making sure to keep the arbor nut clean and free of debris.
Once the blade has been securely fastened, the upper guard can then be closed. Make sure to set the blade height and blade tilt before turning the saw on and beginning to cut. Once the saw is powered, the operator should stand to the side when the blade begins to make contact with the piece of material.
The blade should never be allowed to spin to a complete stop as this will overheat the motor and can damage the saw and the operator.
How do you align a Craftsman radial arm saw?
To align a Craftsman radial arm saw, you will need to make sure all of the components of the arm away are properly aligned and that all components are properly secured and tightened. Start by checking that the cutter is blade is secure and in good condition.
Then, loosen the arm base and remove the pulley cover. Check that the front and rear slots on the arm base are parallel and even and use a straight edge to make sure the arm is properly centered to the saw table.
Next, close the arm and make sure the pivot point is centered on the base. Then, check that the arm is level and secure with bolts. Finally, make adjustments to the bevel and blade height until the blade is aligned with two of the four slots on the top of the saw.
Once all of these steps are complete, you can ensure that your Craftsman Radial Arm Saw is properly aligned and ready to use.
What is the most important thing to remember while using the radial arm saw?
The most important thing to remember when using a radial arm saw is to always use proper safety gear, such as safety glasses and hearing protection, and be sure to follow recommended safety practices.
Additionally, you should always make sure that the saw is set up properly with the correct blade guard and fence settings, as well as ensure that the saw is properly secured to the work table and can’t move or become dislodged while in use.
When making cuts, make sure the wood is securely clamped down and that the saw is running at the right speed. Always keep your hands away from the saw blade, and if making a plunge cut, always move the saw slowly and steadily into the workpiece.
Cut with the grain and keep track of your movement as you make each cut. Finally, after you’ve finished cutting, make sure to turn off the power and wait for the blade to come to a complete stop before making any adjustments or removing pieces from the saw table.
Does anyone use a radial arm saw anymore?
Yes, radial arm saws are still used for various projects. These versatile saws can be great for ripping boards, cutting miters, bevels and other shapes, and making repeat cuts. The main advantage of a radial arm saw is its versatility and the fact that it is easy to set up.
It can also handle large stock and make bevel cuts on the end of a workpiece. Many do-it-yourselfers and professional woodworkers find that a radial arm saw can be a great addition to their shops. Some newer saws come with sliding tables and better safety guards, so they are plenty useful for most woodworkers.
Why were Craftsman radial arm saws recalled?
In December of 2015, Craftsman radial arm saws were recalled due to the blade guard posing a serious risk of laceration and other injuries to users. Specifically, the recalled saws have a pivot bracket blade guard system with an open front design.
If the bracket is not properly locked in place, the blade can be exposed, making it a serious laceration hazard. The recalled saws also had a riving knife that lacked sufficient retention, allowing the riving knife to disengage while the saw is running.
The recall was issued by the US Consumer Product Safety Commission and involved Craftsman 10-inch radial arm saws, model number 137.248830 and 137.248230, manufactured in Mexico. Consumers were advised to immediately stop using the recalled saws and contact Stanley Black & Decker, Inc.
, for a free replacement saw or a full refund.
What can a radial arm saw do?
A radial arm saw is a stationary power saw capable of making precise, straight and accurate cuts. It is most commonly used for crosscutting and ripping lumber, making angular cuts (typically 45 degrees or 90 degrees), and dadoing or rabbeting.
It is also occasionally used for making molding, tenons, and other specialty cuts. Many radial arm saws are designed with an adjustable saw arm, allowing the user to easily make measurements and cuts without having to move and adjust other components.
The saw blade can be configured to make beveled or compound cuts. Radial arm saws are often suited for high-volume woodworking operations and are used for rough-cutting, joinery, molding, paneling, and flooring.
They can also be equipped with a variety of accessories for greater versatility including dado blades, tenon jigs, molding cutters, and miter gauges.
Why are radial arm saws not popular?
Radial arm saws used to be extremely popular in the woodworking community, but in recent years they have become less common. This is due to a variety of reasons. First, radial arm saws require more setup and fine-tuning than more modern saws.
This requires a certain level of skill and expertise that many amateur woodworkers may not possess. Second, radial arm saws take up more space than other types of saws. If one does not have a large dedicate workshop, it may not be practical to have a radial arm saw.
Third, technology has advanced significantly since radial arm saws first became popular. The emergence of more accurate, versatile, and cost-efficient saws has made them a less attractive option for many woodworkers.
The result is that radial arm saws, while still available, are less popular than they used to be.
Is it worth having a radial arm saw?
When deciding if it’s worth having a radial arm saw, there are a few things you should consider. One key factor is how often you will be using it and the type of projects you will be working on. If you plan on using it regularly for intricate woodworking projects, then a radial arm saw will be incredibly productive and a great investment for you.
Radial arm saws offer a wide range of cuts, meaning you could save a lot of time over using other tools, such as a miter saw or circular saw. Also, the saw can provide precise cuts and the adjustable arm can be useful when sawing large pieces of material, such as floorboards and other long length materials.
On the flipside, radial arm saws generally take more space and can be difficult to move around due to their size and weight. They also require careful adjustment, as they can be dangerous if not used and maintained properly.
If you decide to invest in a radial arm saw, make sure you understand all the safety features and how to properly use the saw. This way you can maximize the potential of the saw and ensure you are safe.
Overall, whether or not a radial arm saw is worth having depends entirely on the type of project you plan on working on and the frequency in which you plan to use it. If you plan on using woodworking equipment often and can benefit from the precise, time-saving cuts a radial arm saw can offer, then investing in one could be an excellent investment for you.
Is a radial arm saw better than a table saw?
The answer to this question depends on a variety of factors and what type of project an individual is doing. Radial arm saws tend to be more versatile than table saws, as they are able to cut thinner materials and make more intricate cuts, as well as providing the ability to make angular cuts.
On the other hand, table saws are generally the better choice for working with larger materials, due to their larger blades and better stability. Table saws also generally provide more safety features than radial arm saws, making them better for those with less experience.
Ultimately, the best choice between a radial arm saw and a table saw depends on the specific project, the individual’s specific needs, and their level of experience.
How much is radial worth?
Radial is a commerce technology company that is dedicated to helping retailers of all sizes grow their business, serve their customers, and adapt to the ever-changing marketplace. According to the company’s website, Radial’s comprehensive suite of omnichannel commerce and risk management services helps retailers to “sell smarter and faster, and deliver better customer experiences.
” As of 2021, Radial is estimated to be worth around $680 million. The company is privately held, but is owned by Thomas H. Lee Partners and Silver Lake Partners, two private equity firms. In the summer of 2020, Thomas H.
Lee Partners estimated Radial’s valuation at $1 billion. According to Forbes, Radial is currently experiencing rapid growth, with an estimated 30-50% revenue growth every year. Radial’s CEO Tobias Hartmann expects the company to reach a $2 billion market cap in the near future.
What is the minimum distance should your hand be from the blade of the radial arm miter saw blade at all times?
The general rule is to keep at least 6 inches of distance from the blade of a radial arm miter saw, however the manufacturer’s safety instructions should be followed precisely, as requirements may vary depending on the type of saw.
Additionally, additional protective measures such as wearing gloves, safety glasses and other protective equipment should be employed to reduce the risk of personal injury and ensure safety at all times.
It is also important to keep both hands on the handles of the saw while it is in operation and away from the blade to reduce the risk of serious harm.
What type of cut should you not do with the radial arm saw?
A radial arm saw should not be used to make beveled or compound angle cuts. This is due to the fact that it is designed to move in a single plane only. When trying to make beveled or compound angle cuts, the saw may get jammed because, due to its nature, the blade may be suspended mid-air or the blade may be twisted, thus preventing the cut from being made.
Furthermore, a radial arm saw should never be used to cut lap joints, rabbet or dado joints, and similar hardwood cuts. These types of cuts require a higher degree of precision, which the radial arm saw is not capable of providing.
For these types of cuts, a table saw, miter saw, or router would be much better suited.
