Skip to Content

How do I stop my chainsaw from cutting crooked?

If your chainsaw is cutting crooked it could be caused by a number of different factors. First, check that the bar and chain are in good condition and are sharp. If the bar and chain are not in good condition, then you may need to sharpen it or replace it.

Also, check that the engine is running correctly and check for clogged or damaged spark plugs or other engine parts. You should also check the chainsaw’s chain tension. If the tension isn’t right the bar can bind up, kick and pull the chainsaw off line.

Make sure the chain tension is adjusted properly so that it runs smoothly and isn’t too tight or too loose. Finally, you should check the chainsaw’s lubrication systems and ensure they’re functioning properly by adding chain and bar oil as needed.

If all these things are in good working order and the chainsaw is still cutting crooked, then you may need to take it to a professional for further help.

Why is my chainsaw not cutting straight?

If your chainsaw is not cutting straight, there are a few possible explanations. First, the chain may be dull or damaged. This can cause the chain to jerk and not provide a clean and even cut. Second, the guide bar may be bent, twisted or obstructed, also causing the saw to cut irregularly.

The chain tension could also be too loose or too tight – if the chain is too loose, it will have a tendency to drift off line or not cut consistently. Lastly, it is possible that the chain oiler on your chainsaw is not functioning properly.

If the chain is not receiving proper lubrication, it can cause uneven performance and jam up, leading to an uneven cut. Check each of these potential solutions to ensure your chainsaw is cutting straight.

How do you stop a pinched chainsaw?

To stop a pinched chainsaw, you should first ensure that the chainsaw is turned off and that all of the power sources (gasoline, battery, etc. ) have been disconnected. You should then check the saw chain for any damage, and if there is evidence of wear and tear, the chain should be replaced.

Once the chain is replaced, you can check for any obstructions in the bar space and adjust the tension screw on the side of the machine to tighten the saw chain, which should help prevent further pinching.

Finally, make sure you are wearing the proper safety equipment, including eye protection and hearing protection, when operating the chainsaw.

Should I flip my chainsaw bar?

It depends. Flip your chainsaw bar if you want to reduce wear on the teeth and make it easier to kickback proof your saw. If you notice that teeth on one side of the saw are duller than the teeth on the other side, tipping the bar will help by moving some of the worn teeth to the unworn side and will increase the total lifespan of the saw’s blade.

Additionally, if you use your chainsaw to screw your wood, the act of flipping the bar will reduce the number of turns you must take to bore an individual thread, since the bar has been switched from cutting to the right to left and vice versa.

However, if you are dealing with hardwood or you are using the saw to chop large pieces of wood, flipping the bar may result in inefficient cutting. In such instances, it’d be best to use a new bar.

How tight should a chainsaw chain be?

The tension of a chainsaw chain should be set so that it is tight enough for the drive links to stay engaged with the nose sprocket, but loose enough to allow the chain to move freely around the guide bar.

To check the tension, you should place the chainsaw on a flat surface and try to lift the drive links of the chain up and away from the nose sprocket. If the chain can be moved up 1/4″ to 3/8″ (6mm to 10mm) without much effort, the chain tension is probably correct.

If the chain is too tight, you will be able to move it less than 1/4″ (6mm). If the chain is too loose, you will be able to move the drive links farther than 3/8″ (10mm). In either case, you need to adjust the chain tension.

Many modern chainsaws will have a tensioning screw or lever located near the side cover that can be used to adjust the chain tension. On older models, you will need to loosen the bar nuts and adjust the bar itself to increase or decrease tension.

If the chain becomes loose as you use it, you will need to periodically adjust it to maintain the recommended chain tension.

How do I know if my chainsaw chain is sharp?

The best way to determine if your chainsaw chain is sharp is to visually inspect it. Look for clean, even cutting edges along the length of the chain, and note any nicks or flat spots. If there are any nicks or flat spots, this is an indication that your chain is dull and needs to be sharpened.

Additionally, run your finger along the length of the chain. If the chain is sharp, you should feel a smooth, even edge along the length of the chain. If the chain is dull, you should feel that the chain is serrated or rough to the touch.

If you are still unsure about the sharpness of your chainsaw chain, you can also use a file tool to gently tap along the length of the chain. You should hear a ping sound if the chain is sharp, whereas a dull chain will make a dull thud.

How do you keep a chainsaw straight?

Keeping a chainsaw straight is an essential step in proper chainsaw maintenance. For optimal results, it’s essential to check the chainsaw’s straightness before each use.

To check a chainsaw’s straightness, first start by lightly touching each side of the chain’s drive link connecting the chain to the chainsaw body. If the drive link is skewed, gently straighten it with a wrench.

Make sure to check the chainsaw frequently and ensure that the drive link stays straight. Align the drive link to the chainsaw body.

Next, inspect the bar for any bends or twists in the guide bar. If the guide bar appears bent or twisted, you may need to take it to a professional to repair.

Finally, check the chainsaw’s chain tension. Too much tension can cause the chainsaw to run crooked and off-balance, making it more difficult to keep a chainsaw straight. To check the tension, lightly pull the chain away from the bar.

If it moves the length of two links or more, the chain may be too loose. To tighten the chain, use the chain tensioning screw located near the top of the chainsaw body.

Keeping a chainsaw straight is vital for efficient and safe operation. By following these steps, you should be able to successfully maintain your chainsaw’s straightness.

How do you tell if a chainsaw bar is worn out?

Firstly, look for signs of wear and tear such as the chain cutting poorly or stalling, which can indicate a damaged bar. It’s also important to regularly inspect the bar, paying close attention to the rails, which should be a smooth, consistent surface.

If the rails are pitted, corroded, or burnt, it’s a sign that the bar is worn out, and should be replaced. Additionally, check for signs of rust or other damage to the ends of the bar. If either of the ends show signs of wear, the bar should be replaced.

Lastly, if the tensioning bolt continually needs adjusting to keep the chain tight, it’s a sign that the bar is beginning to wear out and should be replaced. Taking the time to inspect and maintain your chainsaw bar is a crucial step in taking good care of your chainsaw and ensuring its safe operation.

How do you tell if a chain is the right way on a chainsaw?

To tell if a chain is the right way on a chainsaw, you should first identify the side plate of the chainsaw. The side plate will have a flat face with an arrow showing the direction the chain should rotate when the saw is started.

Hold the chainsaw in your hand with the side plate pointing away from you and the chain running away from you. Look for the drive links on the chain, which are holes formed on the drive link that will fit over the nose sprocket of the chain tensioner.

If the drive links are pointing out from the side plate in the direction of the arrow, the chain is correctly mounted. If the drive links are pointing away from the side plate, the chain is on wrong and needs to be adjusted.

How should the teeth look on a chainsaw?

The teeth on a chainsaw should be sharp, angled, and the same size. The teeth should have an alternating pattern of left and right facing blades, and each tooth should be between 8 and 10mm in width.

It is important to sharpen the teeth regularly, as dull blades can make the saw hard to control and can put extra strain on the engine. The teeth should also be well-maintained and regularly cleaned with a soft brush and mild detergent, such as dish soap, to remove any dirt or debris that has built up.

Additionally, a file should be used periodically to ensure that each tooth is correctly angled and sharpened. It is important to replace the chainsaw teeth when they become dull or damaged so that the saw is able to run at its full potential and to ensure your safety.

Which way does a chainsaw blade go?

The correct way for a chainsaw blade to go is with the teeth pointed away from the operator. This is especially important for safety reasons, as the teeth of the blade can cause serious injury if they come in contact with the operator.

To ensure that the blade is facing the right direction, the operator should inspect the blade before each use, making sure that the teeth are pointing away from their body. In addition to inspecting the blade, the operator should double check to make sure that their hands are not in the path of the chainsaw blade.

How do you read a chain on a Stihl chainsaw?

Reading a chain on a Stihl chainsaw is relatively simple. First, inspect the chain and ensure that it is securely mounted in the guide bar. Next, turn the chainsaw so the side of the chain with the grinding marks is facing up.

Pay close attention to the line of the teeth; they should be straight and even, with no kinks. The cutting edges should be sharp and the markings should be clear, with no breaks or missing teeth.

Next, examine the depth gauges to ensure they are at the correct height. The depth gauges should be level to the top surface of the rail in the guide bar. Finally, look into the drive link holes to ensure they are clean and free of debris, oil and grime.

Once you have inspected the level and condition of the chain, you are ready to proceed with cutting. Before beginning, be sure to check all safety guidelines and protocols, such as wearing eye protection and keeping hands away from the chain.

How do you find the pitch of a chain?

The pitch of a chain can be found by measuring the average distance from one link to the next. You will need a ruler or a measuring tape, and the chain must be laid out flat in order for the measurement to be accurate.

Start by measuring from one link’s centre to the next link’s centre. When you have this measurement, divide it by two to find the pitch of the chain. For example, if the measurement was 12 inches, the pitch of the chain would be 6 inches.

For accuracy, take multiple measurements and then average out the results.

What is the difference between .325 and 3/8 chain?

The difference between. 325 and 3/8 chain is the size of the drive links. The. 325 saw chain uses 3/8 inch (. 375) pitch drive links, while the 3/8 saw chain uses. 404 inch pitch drive links. In other words, the drive link (the part at the bottom of the chain) on a.

325 saw chain is 3/8 inch wide, while the drive link of a 3/8 inch saw chain is slightly larger, measuring. 404 inch across.

The larger size drive links on the 3/8 inch chain allow for greater control when cutting. The extra strength of the. 404 inch drive links provides less kickback and less vibration, which result in smoother, faster and more accurate cuts.

Additionally, the. 404 inch drive links helps the chain stay on the bar longer than. 325 saw chain, since the larger size provides a better fit when mounted on the bar.

Therefore, when choosing a saw chain for cutting applications, the size of the drive links should be taken into account. If the application requires precise cutting and more control, the 3/8 inch saw chain with the larger size drive links is the best option.

For heavy-duty cutting and durability, the. 325 saw chain with the smaller size drive links is the best choice.

What does chainsaw kickback look like?

Kickback from a chainsaw is a dangerous event that can cause serious injury or death. It occurs when the teeth of the chainsaw come into contact with the surface or object being cut, causing the chainsaw to abruptly move upwards and out of the operator’s control.

This sudden movement can easily cause an inexperienced or unprepared operator to lose control of the chainsaw and injure themselves or bystanders.

To reduce the risk of kickback, chainsaw operators must practice proper chainsaw techniques and be sure that the chain has been properly tensioned. The chain should also be inspected regularly to make sure that it is sharp and not over stretched.

Proper body posture while operating the chainsaw is crucial and the operator should always keep their body away from any surfaces that may be cut. In addition, it is important to use a bar guard when cutting and to make sure that the chain is running parallel to the length of the bar.

Failure to observe these precautions can result in serious kickback and injury.

What makes a chainsaw bar low kickback?

A chainsaw bar with low kickback is designed with safety in mind. Its design features key safety elements that help protect the user from any dangerous kickbacks that could occur when operating the saw.

Key design elements that contribute to chainsaw bar low kickback include: reduced nose radius, chamfered corners, sprocket tip guard studs, and a chrome-nickel steel composition of the bar itself. The reduced nose radius helps reduce the potential for kickback and is typically about 1/4 the size of a standard nose radius.

The rounded chamfered corners are designed to transport debris away from the chain, allowing for less resistance and reducing the chance of a kickback. The sprocket tip guard studs protect the chain links from wear, and the chrome-nickel steel composition of the bar helps prevent wear and breakage.

Where is the kickback zone on a chainsaw?

The kickback zone on a chainsaw is the area located on the top and bottom of the chainsaw’s guide bar. It is the area where the cutting chain links are exposed when the chainsaw is in operation. This area is particularly hazardous, as it’s where the kickback force is usually generated when the chainsaw binds or stalls.

To help prevent kickback, it is important to operate the chainsaw away from the kickback zone. To do this, you should position your right hand near the front of the guide bar and your left hand at the back near the handle.

This will ensure you are holding the chainsaw far enough away from the kickback zone. Additionally, be sure to keep a firm grip on the chainsaw while in operation, as a loose grip in the kickback zone can cause you to lose control of the machine.

What happens if you run a chainsaw with the brake on?

Running a chainsaw with the brake on can be potentially dangerous and should be avoided. The chainsaw brake works as a safety feature that stops the rotation of the chain when the user releases the trigger.

When it is engaged, it increases the resistance of the motor and can overheat the motor if it is left on for an extended period of time. The motor could ultimately fail, leading to a loss of control of the chainsaw.

Additionally, the chain could become jammed, and the user could risk a loss of limb or injury. For these reasons, it is important to never run a chainsaw with the brake on.

How does a low kickback chain work?

A low kickback chain is a chain specially designed to reduce the risk of kickback, which is a dangerous reaction that can occur when the teeth of the chain come in contact with hard objects. Low kickback chains are often necessary when working with a chainsaw and are a great way to increase safety.

Low kickback chains feature special top plates with small radius corners that reduce the risk of binding, as well as well-rounded depth gauges that minimize the risk of contact with hard objects. Additionally, the chain links are designed to uniformly rotate to minimize the risk of kickback, while specially designed angle cutters help reduce the risk of kickback by ensuring quick and easy removal of debris and debris buildup.

Finally, a low kickback chain features a tie strap that ensures increased safety by keeping the chain in place, reducing the risk of kickback or vibration.

What is a full chisel chainsaw chain used for?

A full chisel chainsaw chain is used for general-purpose cutting and works best for clean cutting of softwood, as well as some hardwood. Full chisel chains are designed with square corner “chisel” cutters that leave a fine finish when cutting, making them ideal for cutting planks, trees, and logs, as well as other softwood materials.

Additionally, full chisel chains feature aggressive teeth which make them well suited for fast, efficient cuts. Full chisel chains are the most common type of chainsaw chain, and are used in most professional grade chainsaws.