To turn your Worx trimmer into an edger, you’ll need to purchase Worx’s edger attachment, which is available for purchase directly from the company’s website. Once you’ve purchased the attachment, you will need to follow the included instructions step-by-step to attach it to your trimmer.
This typically involves the removal of the support cup, followed by the attachment of the edger attachment to the cup. You may also need to secure the edger attachment with screws or bolts and adjust the angle of the attachment if necessary.
Once the edger has been attached, you can begin edging your lawn. To get the best results, make sure to hold the trimmer parallel to the ground and at a consistent angle as you edge. It is important to keep the attachment well lubricated with oil, which is included with the edger attachment, to ensure the best performance.
Be sure to take regular breaks to avoid strain and fatigue.
Can you use trimmer as edger?
Yes, you can use a trimmer as an edger. Most string trimmers are designed for edging and have an attachment near the cutting head that will allow you to use it as an edger. This attachment helps guide the trimmer so that it cuts the grass at an angle, allowing for a neat, even cut along the edge of your lawn and flower beds.
To use a trimmer as an edger, first switch the trim line from standard round line to a square-shaped edging line. This will give you a consistent, clean-cut edge and will prevent the line from breaking.
When using a trimmer as an edger, make sure to keep the head upright at all times, as if you tilt it at an angle you can damage the lawn, and take smaller, slower strokes to keep the edging line even.
If you’re finished edging, take the attachment off and switch back to the round trimmer line for regular trimming.
How do you pivot the head on a WORX trimmer?
To pivot the head on a WORX trimmer, first you need to ensure that the tool is turned off and the battery is removed. Then you will want to remove the cap over the cutting head. At the back of the cutting head, near where the battery attaches, you’ll find a small lever.
Push the lever up and away from the body of the trimmer to unlock the cutting head. You can then rotate the head to the position you want. Make sure to push the lever down and toward the body of the trimmer to secure the head into place.
Then, you can replace the cap and reattach the battery.
How do you use a Worx electric edger?
Using a Worx electric edger is easy! To get started, make sure to read the instructions in the manual and check for any safety warnings regarding the use of the trimmer.
To connect the electric edger, first plug the power cord into a wall socket. If you are using an extension cord, make sure the extension cord is not damaged and the cord plugs into the electric edger securely.
When you’re ready to start edging your yard, turn on the switch and adjust the shaft to the desired position. Unfold the blade guard and press down on the safety switch. Then gently move the edger over your grass and rocks.
To achieve a neat and clean edge, pause occasionally and inspect the edges of your yard to make sure they’re straight.
Carefully guide the edger around any obstacles and make sure to keep a steady, consistent pace. When finished, make sure to turn the edger off and unplug the cord from the wall socket. It’s also recommended to clean the blade guard and blade for any debris or grass clippings.
Store the edger in a safe and dry place when not in use.
How do I use Worx wg163?
Using the Worx wg163 is easy! First, make sure the Worx wg163 is fully charged by plugging the charger into an outlet and charging until the battery indicator light turns green. Once the battery is charged, you’re ready to go.
To assemble the Worx wg163, attach the handle and the support bar to the shaft, and place the trimmer/edger head onto the rotating shaft. Finally, to start the trimmer, press and hold the trigger switch located near the handle.
The trimmer will gradually increase motor speed. To turn off the trimmer, simply release the trigger switch.
To adjust the cutting height, use the telescopic support rod adjuster located on the bottom of the trimmer shaft. Slide the adjuster up or down to set the desired cutting height. Make sure that the cutting head of the trimmer is at the same height as the edge of the support bar.
Once you’re finished trimming, use the trimmer head conversion to switch the Worx wg163 from a trimmer to an edger. To do this, twist the trimmer head counter-clockwise to remove the trimmer head and replace it with the edger head.
Now the Worx wg163 is ready for edging. Use the handle and support bar to guide the edger along a surface for neat and even results.
Using the Worx wg163 is easy and will help you take pride in your yard!
How does the command FEED work on the Worx trimmer?
The FEED function on the Worx trimmer is designed to enable users to extend the cutting line for their trimmer. This is especially useful when trimming thick weedy areas or other difficult slope/terrain.
To use the FEED function, simply press the FEED button on the trimmer head. This will turn on the trimmer and release the cutting line, allowing the user to extend it manually using the accelerator trigger.
After releasing the trigger, the FEED function will allow the user to trim again without needing to manually extend the line. The Worx trimmer has a handy LED indicator light which will alert the user when the cutting line is running low.
This ensures that the user can see clearly when it is time to extend the line again. The Worx trimmer FEED function is easy, effective, and convenient to use!.
Why is my Worx trimmer not working?
If your Worx trimmer is not working, there could be a few possible reasons. First, if the trimmer is corded, you may want to check the power cord to make sure it is plugged in securely. If it is cordless, make sure the battery is properly charged and functioning.
If the battery is dead, you will likely need to replace it. You should also make sure that the trimmer head is not jammed or clogged with debris, which may prevent the trimmer from working properly. You can clear any blockages in the trimmer head by taking it apart and cleaning it out.
Additionally, the trimmer may have a faulty on-off switch that needs to be replaced. If none of these issues solve the problem, you may need to take it to a certified repair shop to have it professionally assessed.
How long does Worx GT battery last?
The Worx GT battery is designed to last for a long time. According to the manufacturer, it is meant to provide long run times of up to 3-4 hours in continuous use. Various factors could affect the battery life, such as the temperature, the type of terrain, and the speed and intensity of the activity.
The battery is also designed to self-regulate, meaning it will automatically adjust the intensity of its output depending on the activity, thus increasing its performance and longevity. In normal use, with regular maintenance and charging, the battery is expected to last for over 1000 cycles.
Should you keep trimmer line in water?
No, you should not keep the trimmer line in water. Keeping the trimmer line in water can cause damage because it can become brittle over time due to the water absorption, wear out quicker, and weaken the strength of the line.
Even if the line is made of plastic, the plastic will break down because of the chemicals in the water. Additionally, parts of the line may start to rust due to the presence of moisture. This can lead to poor performance of your trimmer and even end up in a blockage or clog.
In order to keep your trimmer line in the best condition, it’s recommended to store it in a cool, dry place, away from direct sunlight. That way, it will stay in good condition and avoid damage.
How long should trimmer line last?
The amount of time a trimmer line will last really depends on a variety of factors, such as how strong the line is, how often you use the trimmer, how much grass you cut, how hard it is to cut, and how you handle and care for the trimmer line.
Generally speaking, higher quality trimmer lines are thicker and will last longer than lower quality lines, as well as lines with a thicker diameter. However, all types of trimmer line, regardless of quality, will last longer if you follow certain guidelines, such as sharpening the line regularly, using the appropriate diameter of line for your trimmer, replacing the trimmer head when it becomes worn or bent, and avoid cutting ground cover or near any solid objects.
All of these things can significantly prolong the life of your trimmer line. On average, if you take care of it and use it properly, most trimmer lines should be able to last between 8-12 weeks.
Is Thicker strimmer wire better?
The thickness of the strimmer wire you use for trimming your lawn is important, as it can affect the performance of the tool and the quality of the cut. Generally speaking, thicker strimmer wire is better for hardy weeds, but thin wire is suitable for more delicate plants.
Thicker wires are more durable and can handle tougher trimming tasks, such as cutting through tougher plants and weeds, and can also be used for heavier edging jobs. Thicker wires also last longer and can be sharpened multiple times.
However, they can be more difficult to work with and are often more expensive than thinner wires.
Generally, you will get the best results with a strimmer wire that’s suitable for your specific garden and trimming needs. If you’re unsure of which strimmer wire is best, it’s best to consult with a professional or a manufacturer before making your purchase.
What size line does the Worx trimmer use?
The Worx trimmer uses a 0.065-inch line size for its trimmer spool. The Worx trimmer comes with two spools of pre-wound trimmer line, each of which contains 10 feet of 0.065-inch line. It is recommended to always use Worx-brand trimmer line for best performance, as other brands may cause slips, breakages, and overall poor performance.
Additionally, it is important to make sure that you are using the right size of trimmer line for your machine, as an incorrect size of trimmer line can damage your machine and lead to costly repairs.
Why do people take the guards off string trimmers?
People take the guards off string trimmers for a variety of reasons. Some people may want to get closer to their work and believe that the guard is getting in their way. Others may want to get the job done faster and believe the guard is slowing them down.
Additionally, many people believe the guard interferes with the maneuverability of the trimmer so they take it off. In some cases, string trimmers come off the factory line without guards installed, so users who are unfamiliar with the machine may not know they are supposed to have one.
Finally, many people take the guard off because they think it is preventing them from creating an excellent trim job.
