If your window blinds are too wide, you can cut them to the desired size. Before you cut the blinds, you will need to measure the window opening to determine the desired size of the blinds. Once you have established the measurement, you can mark it on the blinds slat with a pencil as a guide for cutting.
Depending on the type of blinds you have, you will either need to use wire cutters or a utility knife to cut the blinds. Cutting with wire cutters is best for aluminum blinds, while using a utility knife is better for wooden blinds.
Lastly, you want to use caution when cutting the blinds to ensure you do not damage them.
Will Lowes cut blinds for you?
Yes, Lowes will cut blinds for you. In store, they offer custom blinds cutting services which can be done while you wait. They can help you decide on the best measurements as well as offer advice on installation and help you find the right installation hardware.
For in-stock blinds, they typically require pre-measuring and ordering the item prior to your visit to their store. You are also able to purchase a pre-cut blind or shade one size smaller so that you can trim it once you get home.
They offer a variety of options like faux wood, vinyl, aluminum and more in different sizes, as well as light-filtering and blackout options for privacy. Lowes can also provide advice on how to measure and trim your blind properly.
How do you shorten the width of a roller blind?
The width of a roller blind can be shortened by following a few simple steps. First, measure the entire width of the roller blind, including any hemming or other attached trim, and write down the measurement.
Next, decide how much you need to shorten the blind, and make a mark on the blind at that point. Depending on the fabric of your roller blind, you may need to unhem the edges before shortening the blind.
This can be done by carefully removing the hem tape from the edges. Cut the excess fabric off the roller blind at your mark, making sure to keep a small allowance for any necessary hemming. If you unhemmed your roller blind, you will then need to re-hem the edges with hem tape.
Lastly, use a hot iron to secure the hem tape in place. Once complete, your roller blind should now be your desired width.
Can vinyl blinds be cut?
Yes, vinyl blinds can typically be cut down to size. Most come with pre-dimensional fixtures which make a great base for custom cut blinds. Some vinyl blinds can be purchased in a “cut-to-width” style that can be shortened in width using household scissors.
Most home improvement stores also offer a service where they can custom-cut the vinyl blinds to fit perfectly in the desired window. When cutting blinds, it is important to take all necessary measurements for an accurate fit, allowing for overhang and providing enough space for the operating mechanism.
Will Home Depot cut blinds to size?
Yes, Home Depot will cut blinds to size upon request. Many of the blinds sold in Home Depot stores are already cut to size, however, if your window is a unique size then Home Depot associates can assist you with getting the perfect size for your window.
They can cut any type of material, including faux wood, and can customize lengths for vertical and horizontal blinds. When you are purchasing blinds in-store, it is always best to let an associate know the exact measurements that you need; this way, they can ensure that you get the right size for your window.
Some Home Depot stores also offer free in-home consultation services, and the associate that comes to your home can measure the windows and help you find the perfect fit. If you order online, be sure to check the exact measurements of the blinds to ensure they will fit your window.
Can you return blinds that have been cut Home Depot?
Yes, Home Depot offers an option to return cut blinds as long as they are unopened, unused and in their original packaging. Customers should make sure that they have the original purchase receipt. If the blinds have been installed, Home Depot may accept the return at its discretion.
In addition, customers may also be able to take advantage of Home Depot’s satisfaction guarantee, which allows the customer to return the blinds for exchange or refund within 365 days of purchase with their original receipt.
How do you cut vinyl blinds?
To cut vinyl blinds, you will need to measure the windows where the blinds will be installed, and then transfer those measurements to the vinyl blinds so that once you have them in place, you can cut them to the desired size.
You can use a hacksaw for cutting the slats. Ensure that slat size is evenly and correctly measured before starting to cut. Then place the blinds on a flat surface and use a ruler and straight edge to mark the slat size and cut along the marked area.
You may need to use a utility knife to cut off any excess vinyl. For the bottom rail, you should measure it with a tape measure and then move the marks to the blinds with a pencil. Cut the bottom rail with a hacksaw.
Finally, use a clean cloth to wipe down the blinds and make sure that they are smooth and even.
Can you shorten wooden venetian blinds?
Yes, wooden venetian blinds can be shortened without any problem. Most blinds come with adjustment cords which can be quickly and easily trimmed to alter the length of the slats. Most manufacturers recommend that the cords be cut at least one inch wider than the desired length of the blind, as the slats will settle to their shortest length after the adjustment cords are cut and the pull cords are attached.
If the blinds have included finials, you may need to remove them to shorten the slats. Generally, you should measure the desired length of the blind before you make the cut, then pull all of the slats towards the top, adjust them to the desired length and cut the excess cords.
Finally, attach the pull cords and finials, if needed.
How much does it cost to cut blinds?
The cost to cut blinds will depend on the type of blinds being cut and the complexity of the required cut. Most basic cuts start at around $20, while more complex cuts, such as specialty angled cuts, may require a surcharge and can range from $25 to $50.
Most reputable blinds stores will offer free measuring services so that the blinds can be cut exactly as needed. It is important that the measurements are exact, as incorrect measurements may result in blinds not fitting into the designated space.
If the blinds are being cut by hand, the cost may be more since special tools may need to be purchased. It’s always best to check with the retailer for more specific costs.
How long does it take to get custom blinds from Lowe’s?
The time it takes to get custom blinds from Lowe’s depends on several factors, including location, availability of materials, and the amount of customization desired. The process typically takes around four to six weeks from purchase to installation.
First, an installer visits your home to properly measure the blinds and ensure accuracy with your windows. Then the customer must select the blinds for the project and order them. Lowe’s will order the blinds from its suppliers and then call the customer to schedule an installation appointment.
Once the blinds arrive at the store, the customer will be contacted to set up a date and time for the installers to arrive. Installation day typically takes one to two hours depending on the size of the project.
Lowe’s takes pride in ensuring that their customer’s custom blinds are installed perfectly and they strive to complete the entire process as quickly as possible.
Can you get window blinds cut?
Yes, you can get window blinds cut. Many companies offer custom window blinds, which have been designed to fit specific window sizes. You can measure your window and order blinds that can be cut to fit your exact window dimensions.
Many places also offer online ordering and delivery, so you won’t have to drive around to find the right fit. Some local hardware stores or home improvement centers can also cut blinds that you bring in to the store.
If you are not sure how to measure a window for blinds, there are plenty of how-to guides online that provide step-by-step instructions. Furthermore, most companies who sell window blinds can provide helpful tips and advice to ensure that you get the perfect fit for your window.
What tool is used to cut blinds?
A mitre saw is the tool commonly used to cut blinds. Mitre saws are designed to make quick, accurate cuts at various angles and can handle softwood, hardwood, plastic lumber, and composite materials such as PVC, fiber cement trim, or cellular PVC.
Many mitre saws come with a clamping system to hold the material you are cutting which is essential for cutting blinds. For best results, you should use a fine-toothed blade to provide a clean, smooth cut.
Additionally, you may want to use a jig to ensure the blinds are cut accurately and to the desired size. Depending on the type of blinds you are cutting, you may also need other tools such as a drill or a hole saw for the mounting hardware.
