Thompson’s Water Seal is designed to be very easy to clean up, as the product is water-based and can be washed away with warm, soapy water. If there is any residue remaining, use a mild household cleaner such as dish soap or an all-purpose cleaner, and a rag or sponge to carefully wipe away the residue.
Once the cleaner has been applied, rinse the area with warm water. If necessary, you can also use an abrasive pad, such as a heavy-duty scrub pad, to remove tougher spots or streaks. For tough stains, you may need to use a stronger cleaner, such as acetone or mineral spirits, to dissolve it and remove it from the surface.
Always be sure to read the product label for more specific instructions on how to use, clean up and safely dispose of the Thompson’s Water Seal product.
How long does Thompson’s Water Seal take to cure?
Thompson’s Water Seal typically takes between 8-12 hours to cure. It is best to allow the product to fully dry before using the space or walking on treated surfaces and, whenever possible, allow the area to be out of direct sunlight and high humidity during the curing process.
During this time, it is important to keep pets and children away from the area to avoid any skin contact, as the sealer can irritate skin and eyes. For large projects, it might be best to cover the area with plastic to ensure that it maintains proper humidity levels to aide in the cure process.
Can you use too much Thompson water Seal?
Yes, you can use too much Thompson water Seal. Generally speaking, more product is not always better. Thompson Water Seal recommends that only one coat of sealer is required for exterior surfaces, such as decks, patios, and fences.
Using more than one coat may lead to an excessive build-up of product, which can create a filmy or splotchy appearance on the surface. It can also crack or peel after time, which would necessitate more maintenance to repair.
Applying too much sealer can also make the surface slick, so it’s important to wait until the product has dried before using the area. Lastly, if you use too many coats, the water repellency of the treated area may be diminished, as the excess coating will act as a barrier to water.
How many coats of Thompson’s water Seal do I need?
It depends on the specific situation you are working with. Generally, the manufacturer recommends applying one coat of the sealer for decks, fences and siding, two coats for extreme weather conditions, and three coats for surfaces that will be exposed to frequent water contact, such as patios and walkways.
If you live in an area with extreme weather conditions, such as heavy snow and rain, you should use two coats of the sealer to ensure your surfaces are adequately protected. You should always follow the manufacturer’s instructions when using any type of sealer product.
Is Thompson’s Water Seal safe for garden beds?
Yes, Thompson’s Water Seal is safe for garden beds. The product has been used in gardens for many years and is designed to protect wood and masonry-based structures from water, sun and mildew damage.
The protective coating also helps enhance the appearance of wood and masonry while providing a mildew and moisture repellent barrier. The water repellency helps keep water away from the structure, reducing the chances of water damage, while the UV protection helps reduce the damage caused by the sun.
Additionally, its mildew resistance helps control the growth of mildew and other fungi. When applied on wood and masonry surfaces, it will act as a water sealant and provide long-term protection. Furthermore, the product is safe for use around gardens as it does not contain any harsh chemicals that would be harmful to your plants.
What kind of brush do you use for Thompson’s Water Seal?
Depending on the surface you’re looking to seal, the type of brush you should use to apply Thompson’s Water Seal will vary. For larger, flat surfaces, like decks, fences, and siding, a 4”–6” synthetic brush may be best.
For hard to reach places, a paint pad or roller may be suitable for the job. For smaller, detailed surfaces, such as railings and trim, a 1” – 2” brush is more appropriate. If applying Thompson’s Water Seal on a vertical surface like a fence, you might use an angled brush to get the job done more quickly.
For other surfaces, including masonry, use a 3”–4” brush to get into the crevices and cover the surface. It’s important to use only a high-quality brush or paint pad so that the bristles or pad don’t leave residue or clog.
No matter what type of brush you’re using, make sure to check it occasionally while you’re working to avoid leaving thin spots.
Can Thompson’s Water Seal be applied over paint?
Yes, Thompson’s Water Seal can be applied over paint. Thompson’s Water Seal offers a variety of products that are specifically designed to protect and seal painted and unpainted surfaces. It can be applied over existing painted surfaces both inside and outside of your home.
However, it is important to make sure that any existing paint is in good condition and free from any flaking or damaged areas prior to application, as these damaged areas may not be sufficiently sealed with Thompson’s Water Seal.
Additionally, you should always test a small, hidden area of the surface before application to ensure that you are happy with the seal and its overall appearance.
How do you remove water sealer from concrete?
Removing water sealer from concrete is an easy process but may require several steps depending on the severity of the sealer. First, you should start by cleaning the concrete surface with a pressure washer to loosen any dirt or debris.
Once the surface is clean, use a degreaser to help remove the water sealer. If the degreaser does not work, use a scrub brush or grinder with a diamond pad scouring attachment to physically scrape away the sealer.
If you choose to use a chemical remover, make sure to select one that is specifically designed for the water sealer you are trying to remove. Follow the directions on the product and wear the appropriate safety gear when using the remover.
After the sealer has been removed, use a pressure washer to once again clean the surface. Finally, let the concrete dry before resealing or painting.
Does water sealer go on before or after paint?
If you’re looking to paint an exterior surface such as brick, wood, or concrete, it’s generally recommended to apply a water sealer before the paint. This is because the sealer will help protect the paint from the effects of water, sunlight, and other environmental conditions.
It also acts to fill in any porous surfaces and create a uniform, smooth surface better suited to hold a painted finish. When applying water sealer, it’s important to follow the manufacturer’s instructions, as different surface materials may require different procedures.
Additionally, the sealer should be fully cured before adding paint; this usually takes between 24 and 48 hours, depending on the product and the weather. To ensure a longer-lasting paint job, you may also consider applying a primer before the paint itself.
Can you use Thompson water Seal on pressure treated wood?
Yes, you can use Thompson water Seal on pressure treated wood. Pressure-treated wood is wood that has been infused with chemicals to make it more resistant to the elements, including damage from water and moisture.
Thompson Water Seal is a brand of wood sealer and protector formulated to help protect wood from the effects of water and UV damage. The product can be used on pressure-treated wood to help protect it from weathering, warping, splitting, and cracking.
Thompson Water Seal is a water-based sealer that penetrates into the surface of the wood, creating an invisible barrier that helps protect it from the inside out. Applying the sealer to pressure-treated wood helps repel water, dirt, and other elements, making the surface easier to clean and extending the life of your pressure-treated wood.
Before applying Thompson’s Water Seal, you’ll need to clean and prep the surface of the pressure-treated wood to make sure it’s free of dirt, debris, and other contaminants. Be sure to use a brush, sandpaper, or a commercial cleaner to remove the old sealer, if any, and to lightly sand the surface of the wood to open up the wood’s pores.
After cleaning and prepping, be sure to follow the manufacturer’s instructions for application of the Thompson Water Seal.
Can you put waterproofing over painted wood?
Yes, you can put waterproofing over painted wood. It is important to make sure the paint has completely cured and hardened before applying waterproofing. This will ensure that the bonding of the waterproofing to the wood is secure.
Although, some paints are not waterproof even after curing, so it is important to keep this in mind when choosing the paint. It is recommended that you thoroughly clean any dirt, dust, debris, mold, mildew and other contaminants from the wood prior to applying waterproofing.
Also, be sure to repair any damage the wood may have sustained. Once the surface is fully prepped, you can apply a coat of waterproofing over the painted wood.
